Memorizing the Channels |
|
|
|
|
|
| ||
Your PDP can memorize and store all of the available channels for both |
|
|
|
| ||||
and cable channels. After the available channels are memorized, use the CH | and CH |
|
|
|
| |||
buttons to scan through the channels. This eliminates the need to change channels by entering |
|
|
|
| ||||
the channel digits. There are three steps for memorizing channels: selecting a broadcast | Storing Channels in Memory (Automatic Method) |
|
|
| ||||
source, memorizing the channels (automatic) and adding and deleting channels (manual). |
|
|
| |||||
|
|
|
|
|
|
|
| |
Selecting the Video |
|
|
|
| First, select the correct signal source (Ant, STD, HRC, | Ant/ CATV |
| Ant |
|
|
|
| 1 IRC). See steps on previous page. |
| |||
|
|
|
|
|
|
| Channel | |
Before your television can begin memorizing the available channels, you must specify the type of |
| Press the MENU button. Press the UP or DOWN button | Auto Program |
| ||||
| to select “Channel”, then press the ENTER button. |
|
|
| ||||
signal source that is connected to the PDP (i.e., an antenna or a cable system). |
|
|
| Fine Tune |
| 0 | ||
|
|
|
| LNA |
| Off | ||
|
|
|
|
|
|
| ||
|
|
|
|
|
| Ch. Scan |
|
|
Press the MENU button. Press the UP or DOWN |
|
|
|
| ➤ Quick way to access the Automatic Channel Setting : Just press the |
|
|
|
| Channel |
| “AUTO PROG.” button on the remote control. |
|
|
| ||
1 button to select “Channel”, then press the ENTER |
|
| Move | Select | Menu | |||
Ant/ CATV |
| Ant |
|
|
|
|
| |
button. | Auto Program |
|
|
|
|
|
|
|
| Fine Tune |
| 0 |
|
|
|
|
|
| LNA |
| Off |
| Press the UP or DOWN button to select “Auto Pro- |
|
|
|
| Ch. Scan |
|
|
|
| Channel | ||
|
|
|
|
| 2 gram”, then press the ENTER button. |
| ||
|
|
|
|
| Ant / CATV |
| Ant | |
| Move | Select | Menu |
|
| Auto Program |
| |
|
|
|
|
|
| Fine Tune |
| 0 |
|
|
|
|
|
| LNA |
| Off |
|
|
|
|
|
| Ch. Scan |
|
|
Press the LEFT or RIGHT button to select “Ant”, |
| Channel |
|
|
|
|
| |
2 “STD”, “HRC” or “IRC”. |
|
|
| Move | Enter | Menu | ||
Ant/ CATV |
| STD |
|
|
|
|
| |
•If you are connected to an antenna, leave "Ant" | Auto Program |
|
|
|
|
|
|
|
displayed. If you connected cable, press the | Fine Tune |
| 0 |
|
|
|
|
|
LEFT or RIGHT button to the display the type of | LNA |
| Off |
| The PDP will begin memorizing all of the available |
|
|
|
Ch. Scan |
|
|
|
|
|
| ||
cable system: "STD", "HRC", or "IRC". |
|
|
|
| 3 channels. |
|
|
|
(If you are not sure which type of cable system you | Move | Select | Menu |
| After all the available channels are stored, the |
|
|
|
have, contact your cable company). |
|
|
|
| Auto program menu reappears. Press the RIGHT |
| Ant 50 |
|
|
|
|
|
| button to stop. | Auto Program |
| |
|
|
|
|
|
| : Stop |
| |
3 Press the MENU button to exit.
Note
• The PDP automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes.
Note
•STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area.
At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (next page).
32 | 33 |
