Printing on Labels | Samsung ML-6060S, ML-6060N guide

Printing on Labels

Guidelines

•Only use labels recommended for laser printers.

•Do not load more than 25 labels into the Multi-Purpose Tray at a time.

•Verify that the labels’ adhesive material can tolerate fusing temperature of 200°C (392°F) for 0.1 second.

•Make sure that there is no exposed adhesive material between the labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to printer components.

•Do not feed a sheet of labels through the printer more than once. The adhesive backing is designed for one pass through the printer.

•Do not use labels that are seperating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.

1Open the Multi-Purpose Tray and the rear output tray.

2 Load labels with print side up, and against the left edge of the tray. Adjust the guide to fit the width of the labels.

3 When you print on labels, configure the paper source, type and size in the software application. For details, see page 5.3.

Note: To prevent them from sticking together, remove label sheet from the output tray as they are printed out.

4.14 PRINT MEDIA

Image 49

Samsung ML-6060S, ML-6060N manual Printing on Labels, Open the Multi-Purpose Tray and the rear output tray

Contents

Visit us at Page Contents Maintaining Your Printer Using Your Printer with Macintosh SpecificationsUsing Windows PostScript Driver Setting Your Printer with the PS Option --------------E.1 Installing Software from Diskettes Using Your Printer on NetworkPrinter Options Memory and PostScript SIMMs -----------------------H.2 Laser Safety Statement Environmental and Safety Consideration Power Saver Ozone SafetyRadio Frequency Emissions Product Name Laser Printer Model Number Party Responsible for Product Compliance Environmental and Safety ConsiderationInformation to User EC Declaration of Conformity Page Prints at 1200 dots per inch dpi. See Special FeaturesPrints 12 pages-per-minute One-touch last page printing is allowed in the ready mode Special FeaturesOn ML-6060N and ML-6060S Prints in Windows, DOS, and Macintosh Supports Linux Printer Components Page Carefully remove all packing tapes from the printer Unpack Your Printer Install the Toner Cartridge Install the Toner Cartridge Make sure it is flat in the tray at all four corners Load paper with the print side facing down Load Paper To Change Paper Size in TrayPaper overloading may cause paper jams Slide the tray back into the printer Pointer Go to Appendix F, Using Your Printer on Network Go to Appendix B, Using Your Printer with a USB Cable Turn on the Printer Turn on the powerPrint a Demo CD-ROM shipped with your printer contains the following Install the Printer Software Install the Printer Software Before Installing the Printer SoftwareVerify the following If the CD-ROM drive does not automatically run Click Install the Samsung Software-I on your PC PCL/USB PCL Printer Driver Features Starting the Uninstaller Software Installation TipsSamsung ML-6060 Driver Uninstall Samsung ML-6060 Series Program group, select Control Panel Buttons Control Panel Lights Toner Save Control Panel Buttons Control Panel Buttons Cancel jobReprint last page of the job Cleaning the inside of the printer Print demo page and configuration sheetStart manual feeding Control Panel Lights Ready ModeLight status legend Processing Paper out in the manual feed mode Manual feed modePrinting in the manual feed mode Control Panel Lights Chapter Choosing Paper and Other Media When you choose print media, consider the followings Choosing Paper and Other Media Media Sizes and Capacities Paper Guidelines Printing to the Top Output Tray Face down Selecting the Output TrayPrinting to the Rear Output Tray Face up Over 250 sheets of paper, continuously To open the rear output tray Selecting the Output Tray Loading Paper Using Tray 1 or the Optional Tray Loading Paper Using the Multi-Purpose Tray To load paper in the Multi-Purpose Tray Stack height limit mark Using the Manual Feed Sheet of paper is loaded and printed Print the documentRepeat this step for every page to be printed Open the rear output tray and pull the extender Printing on Envelopes Printing on Envelopes Adjust the guide to the left edge of the envelope stack Open the Multi-Purpose Tray and the rear output tray Printing on Labels Printing on Transparencies Printing on Preprinted Paper Printing on Card Stock or Custom-sized Media Adjust the guide to fit the width of the media Printing Multiple Pages on One Sheet of Paper N-Up Printing Open the document you want to print Printing a Document Printing a Document You can also see the printable area Select the Samsung ML-6060 Series PCL Printing Help Canceling a Print JobTo stop a print job from the ML-6060 series printer To stop a print job from the Printers folder To enable this feature from the ML-6060 series printer Using Toner Save ModeTo enable this feature from the software application There are two ways to enable the Toner Save mode Printing on Both Sides of the Paper Manual Duplexing Printing on Both Sides of the Paper Manual Duplexing Printing on Both Sides of the Paper Manual Duplexing Click OK, then start printing Printing Multiple Pages on One Sheet of Paper N-Up Printing Supported Letter, A4, Legal, and Executive Printing Booklets Printing Booklets Fold and staple the pages Printing on Different Paper for the First Fitting Your Document To a Selected Paper Size Printing Posters Printing Poster Setting Graphic Properties Setting Graphic Properties This setting provides solid lines and sharp At each setting and choose the one you like bestVector graphics Raster images To use an existing watermark Printing Watermarks Printing Watermarks Click Delete Click OK Access the printer properties Click the Overlays tab, and click Create Overlay Using Page Overlay Create or open the document you want to print Using Page OverlayOverlay List box Using Page Overlay List box You can delete page overlays that are no longer usedClick Delete Overlay Click OK until you exit the Print dialog box Chapter Saving toner Maintaining Toner Cartridge Toner Cartridge Redistributing Toner If the print remains light Firmly close the cover Cleaning the Outside Cleaning the PrinterCleaning the Inside Turn the printer on Cleaning the PrinterWith toner debris, which should be discarded There is paper loaded in the paper tray Chapter Control panel is on Troubleshooting ChecklistSee PCL 6 or Samsung ML-6060 Solving General Printing Problems Uninstall the printer driver, then Print Configured incorrectlySystem error When more memory is Added Solving General Printing Problems Contact a service representative Exit Windows and rebootTry a print job that you know Check the application’s printer Cleaning Sheet Configuration SheetPrinting Special Pages Demo Output Area Clearing Paper Jams Remove the jammed paper Clearing Paper Jams Replace the stopper and close the rear output tray Replace the exit roller Slide out Tray 1 to expose the jammed paper Input Area Clearing Paper Jams Inside the Printer Clearing Paper Jams Pull the option Tray 2 out of the printer Optional TrayIf you see the jammed paper, remove the paper from the tray Do not mix paper types in the paper tray Tips for Avoiding Paper JamsKeep print media stored in an acceptable environment Do not load wrinkled, creased, damp or highly curled paper Print Quality Checklist Solving Print Quality ProblemsSolving Print Quality Problems Light or feded print Clean the LSU see Solving Print Quality ProblemsIf white vertical streaks appear on Increase the amount of background shading Install a new toner cartridgeNew toner cartridge Correct itself after a few more pages Moisture from the air Can cause this problemAgainst the paper stack Printed Rotating the paper 180 in the paper tray Humidity will cause paper curl. See PaperOutput tray Make sure that paper is loaded properly Try installing a new toner cartridge Clean the inside of the printerContact a service representative Check the paper type and quality. See Paper Power off Troubleshooting Error MessagesPrinter Light Patterns Paper jam System errorDoor open, or no toner cartridge Memory out Insufficient Memory Before Printing box and click OK. From Spool Common Windows Problems Problems in the Chooser Common Macintosh ProblemsChooser Zones box in the Chooser Common Macintosh Problems Printing Errors Installed Troubleshooting PS Errors Appendix a Printer Specifications Overview Paper Specifications Supported Sizes of Paper Paper Specifications Guidelines for Using Paper Paper Output Capacity Printer and Paper Storage Environment Paper should be stored at or near room temperature Minimum Maximum Envelopes Return address Paper Specifications Transparencies LabelsSee Printing on Labels on See Printing on Transparencies on Appendix B Plug the other end into the USB port on the computer Installing the Printer SoftwareAdd New Hardware Wizard dialog box appears. Click Next Installing the Printer Software Set your PC printer port Double-click the System icon Windows 98, select Start Settings Control PanelClick the Device Manager tab QHow can I increase printing speed and quality? Frequently Asked Questions About USB Appendix C System Requirements Macintosh Installation Macintosh Installation Connecting To MacintoshUSB 1.0 compliant cable Turn off the printer and computer 10/100Base-T Ethernet Connector on the back of the printerConnect the other end to the network hub Click Install After installation is complete, click Quit Macintosh Installation Choosing PCL Driver Using PCL DriverPrinting from a Macintosh From the Apple menu, select Chooser Using PCL Driver Click Print when you are finished checking your settings Layout Advanced Printing Color Installing PPD file on the USB-connected Macintosh Using PS Driver Using PS Driver Installing PPD file on the network-connected Macintosh Appendix D About Remote Control Panel for DOS Selecting Print Settings Installing the Remote Control Panel for DOS UsersTo install the DOS Remote Control Panel Language Codes To access the Remote Control Panel Selecting Print Settings Valid range is 0 to 300 seconds Config Test Appendix E Installing PPD Files Setting Your Printer with the PS OptionConnecting with parallel interface, see Click Install the Samsung Software-II on your PC PostScript Installing PPD FilesClick on HaveDisk, click Browse, then choose Select Samsung ML-6060 Series PS To open the properties window from the Printer folderTo open the properties window from inside an application Click Properties to open the properties window Appendix F About Sharing the Printer on a Network Select Properties in the Printers menu Setting Up a Locally Shared Printer Setting Up a Network-Connected Printer Appendix G Click Make your own Diskette set of software Making Installation Diskettes Click Copy all disk images Making Installation Diskettes Installing Software from Diskettes Appendix H Disconnect the Power Cord Precautions Memory and PostScript SIMMs Memory and PostScript SIMMs To install the memory SIMM, continue with StepRotate it up until it snaps into place Reconnect the power cord and turn the printer on Remove the two screws, then remove the plate Network Interface Card Network Interface Card Turn off the printer and unplug all cables from the printer Paper TrayReconnect the cables, then turn the printer on Appendix Installation Linux Driver InstallationInstall Setup Script file configuration Mount -t iso9660 /dev/cdrom /mnt/cdrom Device option Linux Driver Installation Access Features Install Remove Cancel, print jobError messages Face-up tray Features Paper source setting Manual light Install PPD filePaper source setting Network interface Install network card Character voids Checklist Problem solving Print mediaPrinting Booklets Cancel Configuration Specifications Paper Setup printerCleaning sheet Install Save toner