Samsung SCC-C6407P, SCC-C6475P manual Focus Mode, Dis

You can select one of four modes for white balance adjustment as follows:

-ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the color temperature is monitored continuously and thereby white balance is set automatically. The following are the approximate supported color temperature ranges in these modes.

ATW1 : 2500K ~ 9300K(✻1)

ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(✻2)

✻1. If the color temperature is out of this range in ATW1 mode, proper white balance may not be obtained. In that case, select ATW2 mode.

✻2. In ATW2 mode, if one color is dominated in the shooted area, the color can be displayed differently.

Therefore, select the mode which is appropriate for the environment.

-AWC(Auto-Tracing White Balance Control): In this mode, accurate white balance is obtained by pressing [ENTER] while having a white paper in front of the camera. White Balance data will be maintained after set it once. AWC mode is best in locations where the color temperature of light source is constant.

-MANU : If WHITE BAL menu is set to MANU mode, the user can set the white Balance considering the current illumination. Select MANU item and press [ENTER], the sub screen where you can select Manual White Balance will be shown. Use the left/right keys to select 3200K, 5600K or OFF(USER) mode in the PRESET menu.

-3200K : Set color temperature to 3200K

-5600K : Set color temperature to 5600K

-USER : Choose out a proper value from the RED and BLUE graph for color and temperature setup.

FOCUS MODE

In the FOCUS MODE MENU, the Focus method can be set to ONEAF(One Auto Focus), or MF(Manual Focus).

-ONEAF : In the ONEAF mode, it automatically sets the focus after the zoom moves, and operates as the same in the MF mode if the zoom does not move.

- MF : In MANUAL FOCUS MODE the user adjusts the Focus manually. Use the left/right keys to select ONEAF orMF in the FOCUS MODE menu.

(VIDEO SET)
IRIS	ALC...
SHUTTER	OFF
AGC	LOW
WHITE BAL	ATW1
DIS	OFF
FOCUS MODE	ONEAF
SPECIAL	...
EXIT	QUIT

❈The ONEAF setting can be selected only when OFF, 1/100(1/120)~1/10K, AUTO X2 is selected for the SHUTTER menu. Any Other SHUTTER setting(AUTO X4~AUTO X160) causes MF to be selected automatically for the FOCUS MODE menu.

❈ONEAF function may not possible withe types of objects listed below. For such objects, focus manually.

-High intensity objects or objects illuminated with low lighting

-Obejects shot through wet or dirty glass

-Pictures that are a mixture of distant and nearby objects

-White alls and other single-color objects

-Venetian blinds and other horizontally striped objects

E

(VIDEO SET)
IRIS	ALC...
SHUTTER	OFF
AGC	ON
WHITE BAL	MANU...
DIS	ON
FOCUS MODE	ONEAF
SPECIAL	...
EXIT	QUIT

➜

Press [Enter]

(AWB/MANUAL)

PRESET 3200K

RET

SPECIAL

In SPECIAL menu, you can directly adjust REVERSE, Y-LEVEL, C-LEVEL, and DETAIL functions.

- REVERSE : Mirrors the screen horizontally, vertically, or in all directions.

- Y-LEVEL	: It is used to set the levels for the Sync signal and the entire
	brightness signal of the video signal.
- C-LEVEL	: It is used to set the levels for the Burst signal and the entire colour

DIS

The DIS(Digital Image Stabilization) function compensates the camera screen shaking incurred from vibration.

signal of the video signal.

- DETAIL : Controls both horizontal and vertical distinction.

❈It is recommended to deactivate the DIS function in the no vibration environment.

❈From VIDEO SET, if you set SHUTTER to between AUTO X2... and AUTO X128... DIS will be displayed as “---“ (it can operate only in Off mode). You can’t adjust the settings manually.

(VIDEO SET)
IRIS	ALC...
SHUTTER	OFF
AGC	LOW
WHITE BAL	ATW1
DIS	OFF
FOCUS MODE	ONEAF
SPECIAL	...
EXIT	QUIT

➜

Press [Enter]

(SPECIAL)
REVERSE	OFF
Y-LEVEL	(0)I--------
C-LEVEL	(0)I--------
DETAIL	(0)--I-
RET

3-15 3-16