Onnecting Printer Cable | Samsung SCX-1000 Series instruction

01-M30UK(1-6 to 2-11) 5/22/00 3:19 PM Page 4

Chapter 2

Connecting

the Printer Cable

The SCX-1000 Series printer has two interfaces for wide connectivity; parallel and USB. If you are running Windows 98 or higher and your computer is equipped with a USB port, see page 2-6 for connection.

Parallel cable connection

To prevent malfunction, it is strongly recommend that you use the supplied parallel cable with the printer. If you need to purchase another cable, ensure that it is complies to IEEE- 1284.

1 Check that both the printer and the computer are powered off and disconnected from the power point.

2 Plug one end of the parallel cable into the connector on the rear of the printer.

Push the metal clips down to fit inside the notches on the cable plug.

Plug the other end of the cable into the appropriate parallel connector on your computer and fasten it tight.

2-4Setting Up Your Printer

Setting Up Your Printer 2-5

Page 11

Image 11

Samsung SCX-1000 Series manual Onnecting Printer Cable, Parallel cable connection

Contents

00-M30UKCover 5/22/00 408 PM Safety Precautions Introduction Printing Multipage on a Single Print Media 10-10 10-110-2 10-5 Overview Introduction You can easily scan documents and photographs About This Guide USB Port Manual Feeder Printer Components Memo Setting Up Your Printer User’s Guide CD-ROMs SmarThru 2 Guide Power Cord Parallel Cable Parallel cable connection Onnecting Printer Cable USB cable connection Connecting the Printer Cable Loading Paper into the Input Tray Insert cartridges Press Enter/Select Display Press Enter/Select Left CARTRIDGE? appearsRight CARTRIDGE? appears Like this Cartridge type Part numberTo change the alignment value Has printed, the display looks Samsung SmarThru 2 provides you with Printer software printer driverSmarThru 2 program Software Requirements Hardware Requirements Typical recommended Type the mail server address and then click the Next button When you have completed, click Finish Follow the instructions on the screen To uninstall the printer driver, proceed as followsTo uninstall the SmarThru 2 program, proceed as follows Congratulations Click Copy all disk images Use them instead of the CD-ROM to install the software Installing Software from Diskette Using the Control Panel Button Function Printer. Look for the following buttons and their functions Attendance Message Print MediaStatus Message When you choose print media, consider the following Media Dimension Use only undamaged paper Not supported paper typesSmoothness and colour of the paper For best print quality, use inkjet paper Printing Tasks Following procedure describes the general steps required Setting Your Default PrinterDefault printer, follow the procedures as described below Click Printer and select Set as Default Select Start Programs Samsung SCX-1000 Series Using the Status TabUsing the Options Tab Starting the SCX-1000 Series Control Program Each property that the printer provides Using the Cartridges Tab1Selectbar. Start Settings Printers from the Windows task This tab allows you to choose cartridge options Document/Quality Tab Paper Tab Image Making a CopyAdvanced Tab Halftone Number appears on To select the new settingTo cancel a copy in progress press the Stop/Restore button Press ˆ or ¤ until the desired To change Copy Size To change Copy ResolutionTo change Copy Contrast Either Enter/Select or Stop/Restore Press the Special Copy SCX-1000S only Smart Media Function Card care and Storage Press Enter/Select when SDC50002.JPG appearsInserting and Removing Cards Selecting the file stored on the Smart Media Card Images and make copies without a direct link to a PC Press ˆ or ¤ to select the print modeYou can print images captured on digital cameras To delete a image file from the Smart Media card Changing Printer Setting Paper Type appears Maintaining Your Printer Page, complete the following steps To install the print cartridgeTo remove the print cartridge Alignment test page. If you need to print an alignment test To wipe the printheads To clean the printheadsTo clean the Scanner Bed Clean the printheads Printer prints the Help list Not satisfactoryRemove the print cartridge from the printer If you need help, see ‘To Remove the Print Cartridge’ on To restore factory defaults Troubleshooting Lift the Output Tray Paper jams while the printer is feedingPaper jams while printing Pull the Input Tray completely out of the printer Tips for Avoiding Paper Jams Smart Media messages Stop/Restore button Press the Enter/Select Selecting the Default Printer Change the Print Quality to High or Normal When the current job is completed, try again Mode because a lot of memory is required toComputer to ECP mode through Bios setting. It How to set BIOS, refer to the document of your AnyPage Lite does not offer the scan feature Brightness or too low resolution. AdjustAccuracy. Do not forget to set the switch back to Printer in draft mode Pecifications Specification Printer Stafford Park 12, Telford Shropshire TF3 3BJ Replacing the Fitted Plug Index Twain UI