Manuals / Sanyo / TV and Video / VCR

Sanyo RD2QD/NA Output Terminals, REMOTE Jack, Remote control setting, NON REC OUT terminal

Models: RD2QD/NA DTL-4800

1 57

Download 57 pages 41.55 Kb

Page 51

OUTPUT TERMINALS

OUTPUT TERMINALS

REMOTE Jack

You can use a VA-RMN01 Remote Control Unit (sold separately) to control remotely the VCR.

NOTE:

œThe functions not available on the VCR will not operate.

Remote control of the VCR is possible by connecting a remote controller with a circuit such as indicated below, to the REMOTE jack.

NOTES:

œUse a 3.5 mm mini-jack type plug.

œThe connection should be done using a shielded cable no more than 5 meters long.

œThe functions not available on the VCR will not operate.

Remote control setting

The remote control switch 7 can be set to either eject the tape or access the menus.

1Press the MENU button to display the (MAIN MENU 1) menu.

2Press the SHIFT ] button to select the “4. VARIOUS SET 1” line, then press the MENU button.

øThe (VARIOUS SET 1) menu appears.

@@@@<VARIOUS@SET@1>

*THREAD@CHECK@@@@Y

*REMOTE@@@@@@@@@@EJECT

*EXT@TIME@ADJ.@@@01:00

*TAPE@END@OUT@@@@PRE

*EJECT@SET

@@EJECT@MODE@@@@@EJECT1

@@OPERATION@@@@@@SLAVE

3 Press the SHIFT ] button, until the “REMOTE”

setting is flashing.

Remote control circuit

R0 1.2K

R1 0.3K

R2 0.43K

R3 0.51K

R4 0.62K

R5 0.75K

R6 0.91K

R7 1.1K

R8 1.3K

R9 2.0K

R10 2.4K

R11 3.6K

R12 5.6K

The resistance tolerance is 2% or less.

SW0: EJECT

SW1: STOP

SW2: STILL/PAUSE

SW3: REW

SW4: FF

SW5: PLAY

SW6: REC

SW7: EJECT (or MENU)

SW8: Not used

SW9: REC/PLAY SPEED, DATA j

SW10: REC/PLAY SPEED, DATA l

SW11: SHIFT ]

SW12: SHIFT «

4 Press the DATA l (or j) button to select the desired

switch mode.

EJECT . . . . . Switch 7 will eject the tape.

MENU . . . . . Switch 7 will display the menu.

5Press the MENU EXIT button to save the setting.

NON REC OUT terminal

If during recording the VCR enters a mode other than recording (i.e. recording pause, stop mode, etc.), a LOW signal (0 V) is output. If recording is resumed, then a HIGH signal (5 V) is output.

If in the (BUZZER SET) menu, NON REC is set to “Y”, a buzzer will be heard while the VCR is in non recording mode. The buzzer will stop if the STOP button is pressed (the output signal will remain LOW (0 V)).

50

English

Image 51

Sanyo RD2QD/NA, DTL-4800 instruction manual Output Terminals, REMOTE Jack, Remote control setting, NON REC OUT terminal

Contents

INSTRUCTION MANUAL English Français EspañolDIGITAL DTL-4800PRECAUTIONS For the customers in CanadaDeclaration of Conformity Avoiding Electrical Shock and Fire PRECAUTIONSMoisture Condensation Problems LocationPower cord Ni-Cd Battery battery pack Video cassette tape ST-180XZES CONTENTSFEATURES ACCESSORIESLOCATIONS OF CONTROLS AND INDICATORS Front PanelRQPONMLKJ G F9 LOCATIONS OF CONTROLS AND INDICATORS1 Operation Indicators Digital Display7 OFF indicator LOCATIONS OF CONTROLS AND INDICATORSBack Panel LOCATIONS OF CONTROLS AND INDICATORSH I J K L 1 EXT TIMER IN external timer input terminal LOCATIONS OF CONTROLS AND INDICATORSIMPORTANT NOTE INSTALLING THE Ni-Cd BATTERYProtection against power failure CONNECTIONSPower Cord Installation About the memory resetCONNECTIONS ø The MAIN MENU 1 menu appears ON-SCREEN MENUSMain menus Sub-menusON-SCREEN MENUS The menus language will now be the one selected SETTING THE LANGUAGE AND CLOCKLanguage Setting Clock SettingAutomatic Daylight Saving Time Adjustment SETTING THE LANGUAGE AND CLOCKø The DISPLAY SET menu appears CHANGING THE ON-SCREEN DISPLAYSelecting the On-screen Display Changing the Date/Time Display PositionHandling Cassette Tapes Precautions concerning the video cassette tapesVIDEO CASSETTE TAPES Loadingø The VARIOUS SET 1 menu appears Setting the Action to Take When a Cassette is LoadedVIDEO CASSETTE TAPES Correct tape thread check functionIMPORTANT NOTES TAPE MANAGEMENT FUNCTIONOperation If no tape management data is present on the tapeSetting the Tape Management Function TAPE MANAGEMENT FUNCTIONø The TAPE MANAGEMENT menu appears GROUP NO. CONFLICT Tape Management Conflict DisplayPROTECT DAY CONFLICT REC PASS SET CONFLICTø The recording speed mode is displayed on the digital display NORMAL RECORDINGNormal Recording Before starting Record PauseNORMAL RECORDING Recording Speed ModeNORMAL RECORDING Concerning the Number of Times Tapes can be Rerecorded onRecording Check Clog Detectionø The RECORD SET menu appears Setting the Mode at the End of the TapeAction to Take when the Video Signal Deteriorates NORMAL RECORDINGø The VARIOUS SET 2 menu appears Changes to the Recording Speed Mode During RecordingSetup for use with a multiplexer NORMAL RECORDINGø The RECORD SET menu appears AUTOREPEAT RECORDINGAutorepeat Recording ø The REPEAT indicator will lightALARM RECORDING Alarm Recording Settingø The RECORD SET menu appears ALARM RESET IN terminal ALARM RECORDINGAlarm Recording Counter Display Connections to the ALARM IN/OUT Terminalsø The alarm search will start Alarm SearchAlarm Scan ALARM RECORDINGOFFF12F24F48F72F96F120F168 Pre Alarm Recording SettingPost Alarm Recording Setting ALARM RECORDINGø The recording start minutes position starts flashing PROGRAM TIMER RECORDINGø The TIMER SET menu appears ø The recording start hour position starts flashingø The recording start hour position starts flashing PROGRAM TIMER RECORDINGø The TIMER SET menu appears ø The rest of the line settings will change toTo Cancel all Program Timer Recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded PROGRAM TIMER RECORDINGRECORDING USING AN EXTERNAL TIMER INPUT ø The TIMER SET menu appearsø “N” will start flashing Multiplexer Connections Using a MultiplexerTrigger Shot Recording Setup TRIGGER SHOT RECORDINGø Recording will start in series recording mode Series Recording SetupSERIES RECORDING Series recording connectionsø Recording will start in series recording mode Continous Loop Recording SetupSERIES RECORDING Loop recording connection example with 2 VCRsAudio Playback PLAYBACKNormal Playback Tracking ControlField Advance Forward and Reverse TAPE COUNTERPLAYBACK Search Forward and Reverseø Day/time search will start DAY/TIME SEARCHDay/Time Search ø “T/D SEARCH 01 000000” will be displayed on screenSetting and Canceling the Quick Method Security Lock SETTING THE SECURITY LOCKSetting the Security Lock Cancel the Security LockSETTING THE BUZZER ø If using the “SET UP” setting, continue with steps 4 andø The BUZZER SET menu appears CLOCK ADJUSTMENT ø The setting procedure on the first VCR is now completedø The VARIOUS SET 1 menu appears EJECT IN terminal SETTING THE CASSETTE EJECT MODECassette Eject Setup EJECT terminal connectionExample SETUP FOR RS-232C OR RS-485 USEDIP Switches Setup SW NoRS-485 Connection SETUP FOR RS-232C OR RS-485 USESetup for RS-232C or RS-485 Use RS-485 RJ-11 connector layoutSignal direction RS-232C 9-pin connector layoutSETUP FOR RS-232C OR RS-485 USE SignalWARNING OUT Terminal TIMER OUT TerminalOUTPUT TERMINALS TAPE END OUT TerminalNON REC OUT terminal Remote control settingOUTPUT TERMINALS REMOTE JackAbout the Backup Lithium Battery MAINTENANCEInspection Procedure Cabinet CleaningPARTS MAINTENANCEMaintenance Table Maintaining and Checking The MechanismTROUBLESHOOTING GUIDE After a Power FailureSystem Down Other Specifications SPECIFICATIONSGeneral Specifications ConnectorsWhere Purchased SANYO INDUSTRIAL VCR WARRANTYOBLIGATIONS EXCLUSIONSPrinted in Japan Issue No1AC6P1P2110- -B RD2QD/NA 0601KP-01