Sanyo DVR-HT120 Symptom, Cause, Solution, Moisture Condensation, Moisture condensation can occur

Symptom		Cause		Solution
Cannot record or did not record	-	The remaining blank space on the disc is insufficient.	-	Use another disc.
successfully.
	- The source you are trying to record is copy-protected.		- You can not record the source.
	- When setting the recording channel, the channel is tuned		- Select the channel on the DVD Recorder’s built-in
		on the TV’s own tuner.		TV tuner.
	-	When recording to disc, programs that are copy-once	- You can not record the source.
		protected cannot be recorded.
	- The disc is recorded on NTSC on other equipment.		- You can not record on the disc already recorded on
				NTSC. Replace a disc.
Timer Recording not possible.	-	Clock in the DVD Recorder is not set to correct time.	- Set clock to correct time. See “Setting the Clock”
				on page 15.
	- Timer has been programmed incorrectly.		- Reprogram Timer. See “Timer Recording” on page
				18.
	- TIMER indicator light does not appear after programming		-	Reprogram Timer.
		timer.
Stereo Audio Record and/or	-	TV is not Stereo-compatible.	-	No solution.
Playback not present.
	- Broadcast program is not in stereo format.		-	No solution.
	- DVD Recorder A/V Out jacks are not connected to TV		- Make A/V connections. Stereo is available only via
		A/V In jacks.		A/V output from DVD Recorder.
	- DVD RecorderAudio/Video Out is not selected for viewing		- Select AUX or A/V source as TV input.
		on the TV.
	- DVD Recorder’s TV audio channel is set to MONO.		- Set TV audio channel mode to Stereo. See “Audio
				Output Settings” on page 32.
Remote control does not work	-	The remote control is not pointed at the remote sensor	-	Point the remote control at the remote sensor of
properly.		of the DVD Recorder.		the DVD Recorder.
	- The remote control is too far from the DVD Recorder.		- Operate the remote control within 6m.
	- There is an obstacle in the path of the remote control		-	Remove the obstacle.
		and the DVD Recorder.
	- The batteries in the remote control are exhausted.		- Replace the batteries with new ones.
Playback starts midway after a	-	If the Resume function is on, playback starts from the	- Turn the Resume function off. See "Operation and
DVD video is inserted and the		previous position where that disc was stopped for the		State Display Settings" on page 32.
6 button is pressed.		next 20 discs.

Moisture Condensation

	Moisture condensation can occur:		In locations where moisture condensation may occur:
-	When the DVD Recorder is moved from a cold place to a warm	-	Keep the DVD Recorder plugged into an AC power outlet with POWER
	place.		on. This will help prevent condensation.
-	Under extremely humid conditions.	-	When condensation has occurred, wait a few hours for the DVD Recorder
			to dry before using it.

Reset the DVD Recorder

If you observe any of the following symptoms:

-When the DVD Recorder is plugged in, but the power will not be turned on or off

-When the display window does not work

-When the DVD Recorder does not operate normally

Before resetting, please proceed the following procedure first.

1.Turn the o button off.

2.Disconnect the Power lead.

If these operation does not work, reset the DVD recorder as follows.

You can reset the DVD Recorder as follows:

1.Disconnect the DVD Recorder from the power outlet.

2.Press and hold down the o button on the front of the recorder while reconnecting to the power outlet.

3.Release o when “IS TV ON?” appears in the display.

4.Complete the first installation again and reset any items you have adjusted during your use of the recorder.

Warning!!

-The information stored in memory may be reset (cleared).

37