Lamp counter resetting, Item, Description | Sanyo PLCXL51 specs

Lamp counter resetting

		Setting up the projector
	Item	Description

	Key lock	Sets the prohibition of controls either Projector or
		Remote control.
	Fan	Sets the cooling options after turning off.
		L1 Normal cooling
		L2 Silent cooling
	Fan control	Sets the fan control speed.
		Off Normal mode
		On1 Highland mode 1
		On2 Highland mode 2
	Zoom	Sets the zoom function. (Reset, Memory1, Memory2)
	Uniformity Adj	Sets the uniformity adjustment. (Reset, Memory1,
		Memory2)
	Terminal	Sets the COMPUTER IN 2/MONITOR OUT terminal to
		Computer 2 or Monitor Out.
	Item	Description

	Lamp
	Corres. Value (h)	Displays the lamp use time (Corresponding value) .
		Reset the time after the lamp is replaced.

Lamp counter resetting

1.Select a Lamp radio button and then click Reset button.

2.Click OK button to execute the reset.

Filter counter	Displays the filter use time. Reset the time after filter
	clean-up.
Filter warning	Sets the time to indicate the filter warning message on
	the screen.

Item	Description

Factory default	Sets all of the projector control items to the factory
	default setting except the following items.
	Lamp Corres. Value, PJ time, Filter time, PIN code lock
	and Logo PIN code lock.
P-TIMER	Switches the P-TIMER display.
	ON	Starts P-TIMER indication
	STOP	Stops P-TIMER counting
	OFF	Stops P-TIMER indication

73

Image 73

Sanyo PLCXL51 owner manual Lamp counter resetting, Item, Description

Contents

Projector Set-upand Operation Network Capture Wired and Wireless SettingNetwork Viewer Moderator Function Network Set-upand Operation For Windows Federal Communications Commission Notice ComplianceFor Canadian Users FCC Warning English CAUTION IN USING THE PROJECTOR VIA NETWORKS Safety instructionsCAUTION IN USING NETWORK FUNCTION Caution about Radio Wave 2. Setup procedures Table of contents4. Wired LAN configurations 5. Wireless LAN configurations 8. Network capture functions 7. Controlling the projector9. Network Viewer functions 10. Appendix Required operating environment for computers Operating environment and configuration Wireless LAN Network specifications of the projectorLAN Terminal Compliance 1. About LAN functions Chapter Image projecting system via LAN LAN functions and the featuresFlow of Image Transfer Chapter 1 About LAN functions An example of the connection An example of the connection LAN connection modes Computer1 LAN connection modesComputer2 Chapter 1 About LAN functions This chapter describes how to install the Network 2. Setup proceduresCapture 5 software and how to set up the networks LAN and set the configuration STEP 1 Install the software on computersSTEP 3 Network Configuration has completed Select Wired LAN or Wireless LAN then connect the Network Viewer & Capture 5 installation Installing the softwareInstalling the software 3 Click Finish to complete the installation Network Capture Installed softwareNetwork Viewer 5 File Converter Network Viewer 5 Program Editor Installed software and places File Converter 2 installation 3.Names and functions of the operation screen Network connection standby display Parts Names and Functions of the Screen Network Capture 5 windowNetwork Capture 5 window Note on Windows Vista Using the multiple network adaptors 4. Wired LAN configurations Network environment settings Connecting to the LAN lineSetting Procedure Chapter 4 Wired LAN configurations 4. Press SELECT button Network environment setting Confirming the operation Network Projector list Confirming the operationSpecify IP button Search specified IP address window Network PIN code Wired factory defaultNetwork information Wired LAN factory default settings Wired LAN factory default settingsSELECTED LAN MANUAL Chapter 4 Wired LAN configurations 5. Wireless LAN configurations Setting procedures Setting the network environmentChapter 5 Wireless LAN configurations “Confirming the Operation” p.28 Setting the network environment Notes when entering characters Configuring security with the projector Use of security type WEP Configuring security with the projector Available PSK key characters Use of security type WPA-PSK, WPA2-PSK Setting Procedures Easy wireless settingEasy wireless setting Computer environment and Wireless LAN connection Wireless factory default WIRELESS indicator display WIRELESS indicator display Selected LAN Wireless LAN factory default settings 6. Basic setting and operation Chapter 6 Basic setting and operation Select a display mode and loginStarting up the Browser STANDARD MODE zMain setting page in the Standard Mode display Display of main setting pageSetting page Starting up the browser xMain setting page in the Light Mode display How to use the setting pageExample of the Setting Page Setting Pallet How to use the setting page Type of the setting palletText box setting Pull-downmenu setting Switches PJLink password authentication on or off Initial settingPassword for PJLink function Japanese PJLink and password setting Network PIN code settingInitial setting Whats PJLink? Auto setting Date and time settingManual setting Setting of LAN Network configurationNetwork configuration 3.After completing the network configuration, press Regist button to register the network information. The SimpleWireless setting is fixed, which cannot be changed from factory default value Item Configuring wireless LAN settingDescription WPA-PSKand WPA2-PSKmode are not available Notes for entering characters Configuring wireless LAN security setting 1Setting SMTP server and administrator address E-mailsettingE-mailsetting Administrator 3Option selection for sending alert mail 2Registering and deleting E-mailaddresses When internal PJ temperature is too high Examples: Type and contents of alert mailWhen internal PJ power circuit is failed When PJ lamp replacement time is reached SNMP setting SNMP settingEnter user name of the projector etc. optional Enter place of the projector optional public Check and delete the trap addressUp to 10 trap addresses can be registered Trap option setting Chapter 6 Basic setting and operation 7. Controlling the projector Chapter 7 Controlling the projector Power control and status checkPJ status PJ temp 1.Select “Setting” from the Projector menu Power control and status checkAbout projector condition Input Controls Available selection at the RGB input SystemAvailable selection at the Component input Controls Input source Image adjustmentImage mode Video Computer Adjusts the sound volume from the speakers SoundSuppresses the sound PC adjustment Setting up the projector Setting up the projectortable below Screen mode Description Lamp counter resetting How to set the timer Timer settingTo set the timer event on specified date 1Set a day or date Timer setting Check the timer eventsChange the event mode 2Set an execute time Projector Power Notes on timer settingEvent Event Projector information Projector informationDisplays selected signal system Input signal status Displays the timer setting status Indication of the lamp statusTimer has been set No timer setting Multi-control Controlling and setting the multi-projectorsExample of multi control Multi-control Start/stop the multi control Multi control setting Confirmation of registered projector Register the projectorEnter projector name or installed location etc Enter IP address of the projector to control Status Change the mode of the registered projectorMode Check & Change page in the light mode Setting all togetherControlling all together Check & Change page in the light mode Viewer auto setting all together Real Time Capture Network Communication 8. Network capture functionsModerator Function Start up the Network Capture About Network Capture functionReal Time Capture +p.89 Network Communication +p.94 About Network Capture function Commands on the task barMenu during Real time capturing Menu during Moderator function Parameter set up Using the Real Time Capture Using the Real Time CaptureRegistering the computers 1 Control by the computer 2 Control by the web browser Using the real time capture 3 Control by the projector 4 Control by the computer with USB memory Using the Network Communication Using the Network Communication Settings before using the Network Communication Description of capture editing window Menu treeMenu Submenu Tool bar button names Command ToolBar of Main PC tool bar How to acquire and release the editing authority How to use the Network communicationStart the communication Join the communication only for Sub PC How to use the Network communication Setting of the drawing tool attributeEdit capture image Drawing figures Drawing letter Letter attribute setting On the Communication PreparationOperation on the Main PC Operation on the Sub PC Executing the forcing mode Moderator function Moderator functionModerator Clients Normal mode application window Preparation for using the moderator functionModerator mode application window Description of application window Using the moderator functionModerator operation Client operation Unregister moderator status Moderators password setting up Error information Error informationError messages Cause and corresponding Chapter 8 Network capture functions 9. Network Viewer functions Creating the available data Network Viewer 1 How to use the Network Viewer 5 File ConverterStart up and quit the File Converter Chapter 9 Network Viewer functions Creating the available data Command Tool ButtonMenu Tree Sub Menu 2 When converting each file, select a preview image first and then click Convert each file Output destination Setting of output destination and conversion modeConversion mode Folder 2 How to use the Network Viewer 5 File Converter Creating a program file Program Editor Procedure of making programCreating a program file Program Editor 4 Click New button 1 Select a folder list contains images to change Image frame on the index window The limitation of the Program file Example of the created program selection 1 Control by the web browser Using the Network Viewer functionCondition to use the Network Viewer function Using the network viewer function 2 Setup the setting page 1 of the Visual display1 IMPORTANT NOTICE Enter your login account of the FTP server Switches to the thumbnail mode Switches to the List modeDecides a image to start auto display with 4 Auto Display setting and control page 2Control by the projector Error informationDescription Error type Display time of the image 3 to 240 sec Display time Repeat timesTimes Auto Chapter 9 Network Viewer functions Firewall setting Troubleshooting Terminology Use of telnet Web browser setting10. Appendix Control Use of telnetChapter 10 Appendix Use of telnet Command list table Active Script/JavaScript enable Web browser settingFlash Player enable Proxy setting Flash Player enable ActiveScript settingWeb browser setting ActiveX controls and plug-inssetting Flash Player Add-onsetting Proxy settingUsing proxy server Not using proxy server Flash Player Plug-insetting JavaScript SettingNetscape Navigator Using proxy server Firewall setting Firewall setting The computer cannot connect projectors Wired LAN TroubleshootingWireless LAN Wireless LAN Connection cannot be established Infrastructure Mode TroubleshootingCannot start up the browser Cannot be turned on/off with the web browser Network capture Speed of playing back images are very slow File Converter Network ViewerI cannot make a new program file What kind of image formats can I convert? Troubleshooting ESSID Extended Service Set Identifier DHCP server Dynamic Host Configuration ProtocolWEP Wired Equivalent Privacy Wi-Fithe Standard for Wireless Fidelity Terminology SANYO Electric Co., Ltd SO-WIN-KV7A