Network specifications of the projector, Compliance | Sanyo PLCXL51

Network specifications of the projector

Network specifications of the projector

LAN Terminal

	Data communication speed	100Base-TX (100Mbps)/10Base-T (10Mbps)

	Protocol	TCP/IP

Wireless LAN

	Interface	IEEE802.11b/g

	Communication Mode	AdHoc,
	Communication Mode	Infrastructure
		Infrastructure

	Data Transfer Speed	1/2/5.5/11Mbps (IEEE802.11b)
	Data Transfer Speed	6/9/12/18/24/36/48/54Mbps (IEEE802.11g)
		6/9/12/18/24/36/48/54Mbps (IEEE802.11g)

	Wireless Frequency (Channel)	2412MHz–2462MHz (CH1–CH11)

		IEEE802.11g OFDM
		54/4Mbps 64QAM, 36/24Mbps 16QAM, 18/12Mbps
	Modulation Form	QRSK, 9/6Mbps BPSK
		IEEE802.11b DSSS
		11/5Mbps CCK, 2Mbps DQPSK, 1Mbps DBPSK

	Protocol	TCP/IP

		WEP 64Bit (Open/Shared) /WEP 128Bit (Open/Shared),
	Security	WPA-PSK(TKIP), WPA2-PSK(AES),
		SSID, ESSID

	Service area	about 30 m (without disturbance)
	Service area	Differs according to the operating environment.
		Differs according to the operating environment.

Compliance

Countries and Standards

JAPAN: VCCI ClassB,TELEC (Wireless)

USA: FCC Part15 Subpart C (Wireless) FCC Part15 Subpart C, Class B

Canada: IC RSS-210 (Wireless), IC ICES-003 ClassB

Europe: R&TTE, EMC, LVD

8

Image 8

Sanyo PLCXL51 owner manual Network specifications of the projector, LAN Terminal, Wireless LAN, Compliance

Contents

Wired and Wireless Setting Projector Set-upand Operation Network CaptureNetwork Viewer Moderator Function Network Set-upand Operation For Windows Compliance Federal Communications Commission NoticeFor Canadian Users FCC Warning English Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKSCAUTION IN USING NETWORK FUNCTION Caution about Radio Wave Table of contents 2. Setup procedures4. Wired LAN configurations 5. Wireless LAN configurations 7. Controlling the projector 8. Network capture functions9. Network Viewer functions 10. Appendix Operating environment and configuration Required operating environment for computers Network specifications of the projector Wireless LANLAN Terminal Compliance Chapter 1. About LAN functions LAN functions and the features Image projecting system via LANFlow of Image Transfer Chapter 1 About LAN functions An example of the connection An example of the connection LAN connection modes Computer2 LAN connection modesComputer1 Chapter 1 About LAN functions Capture 5 software and how to set up the networks 2. Setup proceduresThis chapter describes how to install the Network STEP 1 Install the software on computers LAN and set the configurationSTEP 3 Network Configuration has completed Select Wired LAN or Wireless LAN then connect the Installing the software Installing the softwareNetwork Viewer & Capture 5 installation 3 Click Finish to complete the installation Installed software Network CaptureNetwork Viewer 5 File Converter Network Viewer 5 Program Editor File Converter 2 installation Installed software and places 3.Names and functions of the operation screen Network connection standby display Network Capture 5 window Parts Names and Functions of the ScreenNetwork Capture 5 window Note on Windows Vista Using the multiple network adaptors 4. Wired LAN configurations Connecting to the LAN line Network environment settingsSetting Procedure Chapter 4 Wired LAN configurations Network environment setting 4. Press SELECT button Confirming the operation Confirming the operation Network Projector listSpecify IP button Search specified IP address window Network information Wired factory defaultNetwork PIN code Wired LAN factory default settings Wired LAN factory default settingsSELECTED LAN MANUAL Chapter 4 Wired LAN configurations 5. Wireless LAN configurations Chapter 5 Wireless LAN configurations Setting the network environmentSetting procedures Setting the network environment “Confirming the Operation” p.28 Configuring security with the projector Notes when entering characters Configuring security with the projector Use of security type WEP Use of security type WPA-PSK, WPA2-PSK Available PSK key characters Easy wireless setting Easy wireless settingSetting Procedures Wireless factory default Computer environment and Wireless LAN connection WIRELESS indicator display WIRELESS indicator display Wireless LAN factory default settings Selected LAN 6. Basic setting and operation Select a display mode and login Chapter 6 Basic setting and operationStarting up the Browser STANDARD MODE Display of main setting page zMain setting page in the Standard Mode displaySetting page Starting up the browser How to use the setting page xMain setting page in the Light Mode displayExample of the Setting Page Setting Pallet Type of the setting pallet How to use the setting pageText box setting Pull-downmenu setting Initial setting Switches PJLink password authentication on or offPassword for PJLink function Japanese Network PIN code setting PJLink and password settingInitial setting Whats PJLink? Manual setting Date and time settingAuto setting Network configuration Network configurationSetting of LAN 3.After completing the network configuration, press Regist button to register the network information. The SimpleWireless setting is fixed, which cannot be changed from factory default value Configuring wireless LAN setting ItemDescription WPA-PSKand WPA2-PSKmode are not available Configuring wireless LAN security setting Notes for entering characters E-mailsetting 1Setting SMTP server and administrator addressE-mailsetting Administrator 2Registering and deleting E-mailaddresses 3Option selection for sending alert mail When internal PJ power circuit is failed Examples: Type and contents of alert mailWhen internal PJ temperature is too high When PJ lamp replacement time is reached SNMP setting SNMP settingEnter user name of the projector etc. optional Enter place of the projector optional Up to 10 trap addresses can be registered Check and delete the trap addresspublic Trap option setting Chapter 6 Basic setting and operation 7. Controlling the projector Power control and status check Chapter 7 Controlling the projectorPJ status PJ temp About projector condition Power control and status check1.Select “Setting” from the Projector menu Controls Input System Available selection at the RGB inputAvailable selection at the Component input Controls Image adjustment Input sourceImage mode Video Computer Suppresses the sound SoundAdjusts the sound volume from the speakers PC adjustment Setting up the projector Setting up the projectortable below Screen mode Chapter 7 Controlling the projector Lamp counter resetting Timer setting How to set the timerTo set the timer event on specified date 1Set a day or date Check the timer events Timer settingChange the event mode 2Set an execute time Notes on timer setting Projector PowerEvent Event Projector information Projector informationDisplays selected signal system Input signal status Indication of the lamp status Displays the timer setting statusTimer has been set No timer setting Controlling and setting the multi-projectors Multi-controlExample of multi control Multi-control Multi control setting Start/stop the multi control Register the projector Confirmation of registered projectorEnter projector name or installed location etc Enter IP address of the projector to control Mode Change the mode of the registered projectorStatus Setting all together Check & Change page in the light modeControlling all together Check & Change page in the light mode Viewer auto setting all together Moderator Function 8. Network capture functionsReal Time Capture Network Communication About Network Capture function Start up the Network CaptureReal Time Capture +p.89 Network Communication +p.94 Commands on the task bar About Network Capture functionMenu during Real time capturing Menu during Moderator function Parameter set up Registering the computers Using the Real Time CaptureUsing the Real Time Capture 1 Control by the computer Using the real time capture 2 Control by the web browser 3 Control by the projector 4 Control by the computer with USB memory Using the Network Communication Settings before using the Network Communication Using the Network Communication Menu tree Description of capture editing windowMenu Submenu Command Tool Tool bar button namesBar of Main PC tool bar How to use the Network communication How to acquire and release the editing authorityStart the communication Join the communication only for Sub PC Setting of the drawing tool attribute How to use the Network communicationEdit capture image Drawing figures Letter attribute setting Drawing letter Preparation On the CommunicationOperation on the Main PC Operation on the Sub PC Executing the forcing mode Moderator function Moderator functionModerator Clients Moderator mode application window Preparation for using the moderator functionNormal mode application window Using the moderator function Description of application windowModerator operation Client operation Moderators password setting up Unregister moderator status Error information Error informationError messages Cause and corresponding Chapter 8 Network capture functions 9. Network Viewer functions 1 How to use the Network Viewer 5 File Converter Creating the available data Network ViewerStart up and quit the File Converter Chapter 9 Network Viewer functions Command Tool Button Creating the available dataMenu Tree Sub Menu 2 When converting each file, select a preview image first and then click Convert each file Setting of output destination and conversion mode Output destinationConversion mode Folder 2 How to use the Network Viewer 5 File Converter Creating a program file Program Editor Procedure of making programCreating a program file Program Editor 4 Click New button 1 Select a folder list contains images to change Image frame on the index window Example of the created program selection The limitation of the Program file Condition to use the Network Viewer function Using the Network Viewer function1 Control by the web browser 2 Setup the setting page 1 of the Visual display Using the network viewer function1 IMPORTANT NOTICE Enter your login account of the FTP server Switches to the List mode Switches to the thumbnail modeDecides a image to start auto display with 4 Auto Display setting and control page Error information 2Control by the projectorDescription Error type Display time Repeat times Display time of the image 3 to 240 secTimes Auto Chapter 9 Network Viewer functions 10. Appendix Use of telnet Web browser settingFirewall setting Troubleshooting Terminology Chapter 10 Appendix Use of telnetControl Command list table Use of telnet Web browser setting Active Script/JavaScript enableFlash Player enable Proxy setting ActiveScript setting Flash Player enableWeb browser setting ActiveX controls and plug-inssetting Proxy setting Flash Player Add-onsettingUsing proxy server Not using proxy server Netscape Navigator JavaScript SettingFlash Player Plug-insetting Proxy setting Firewall setting Firewall setting Troubleshooting The computer cannot connect projectors Wired LANWireless LAN Wireless LAN Connection cannot be established Cannot start up the browser TroubleshootingInfrastructure Mode Network capture Cannot be turned on/off with the web browser Speed of playing back images are very slow Network Viewer File ConverterI cannot make a new program file What kind of image formats can I convert? Troubleshooting DHCP server Dynamic Host Configuration Protocol ESSID Extended Service Set IdentifierWEP Wired Equivalent Privacy Wi-Fithe Standard for Wireless Fidelity Terminology SO-WIN-KV7A SANYO Electric Co., Ltd