Indication of the lamp status, Items, Description

Chapter 7 Controlling the projector

Indication of the lamp status

Icon display/background	Status

White-Yellow/Blue	Lamp on (Normal)

White-Yellow/Red	Lamp on (Lamp is being used over a specified use time, replace lamp immediately)
White-Yellow/Red

Gray/Blue	Lamp off (Normal)
Gray/Blue

Gray/Red	Lamp off (Lamp is being used over a specified use time, replace lamp immediately)
Gray/Red

Red/Blue with X	Lamp failure (Lamp failure, check the lamp condition)
Red/Blue with X

Red/Red with X	Lamp failure (Lamp failure and lamp is being used over a specified use time, replace
Red/Red with X	the lamp immediately)

Items	Description

PJ time	Displays the accumulated use time of the projector.
Lamp Corres.
Value	Displays the use time (Corresponding value) of the
	lamp.
Filter time	Displays the use time of the filter.
Timer	Displays the timer setting status.
	ON	Timer has been set.
	OFF	No timer setting.

Page 78

Image 78

Sanyo PLCXL51 Indication of the lamp status, Controlling the projector, Items, Description, Lamp Corres, No timer setting

Contents

Network Viewer Moderator Function Wired and Wireless SettingProjector Set-upand Operation Network Capture Network Set-upand Operation For Windows For Canadian Users ComplianceFederal Communications Commission Notice FCC Warning English CAUTION IN USING NETWORK FUNCTION Safety instructionsCAUTION IN USING THE PROJECTOR VIA NETWORKS Caution about Radio Wave 4. Wired LAN configurations Table of contents2. Setup procedures 5. Wireless LAN configurations 9. Network Viewer functions 7. Controlling the projector8. Network capture functions 10. Appendix Operating environment and configuration Required operating environment for computers LAN Terminal Network specifications of the projectorWireless LAN Compliance Chapter 1. About LAN functions Flow of Image Transfer LAN functions and the featuresImage projecting system via LAN Chapter 1 About LAN functions An example of the connection An example of the connection LAN connection modes LAN connection modes Computer1Computer2 Chapter 1 About LAN functions 2. Setup procedures This chapter describes how to install the NetworkCapture 5 software and how to set up the networks STEP 3 Network Configuration has completed STEP 1 Install the software on computersLAN and set the configuration Select Wired LAN or Wireless LAN then connect the Installing the software Network Viewer & Capture 5 installationInstalling the software 3 Click Finish to complete the installation Network Viewer 5 File Converter Installed softwareNetwork Capture Network Viewer 5 Program Editor File Converter 2 installation Installed software and places 3.Names and functions of the operation screen Network connection standby display Network Capture 5 window Network Capture 5 windowParts Names and Functions of the Screen Note on Windows Vista Using the multiple network adaptors 4. Wired LAN configurations Setting Procedure Connecting to the LAN lineNetwork environment settings Chapter 4 Wired LAN configurations Network environment setting 4. Press SELECT button Confirming the operation Specify IP button Confirming the operationNetwork Projector list Search specified IP address window Wired factory default Network PIN codeNetwork information SELECTED LAN Wired LAN factory default settingsWired LAN factory default settings MANUAL Chapter 4 Wired LAN configurations 5. Wireless LAN configurations Setting the network environment Setting proceduresChapter 5 Wireless LAN configurations Setting the network environment “Confirming the Operation” p.28 Configuring security with the projector Notes when entering characters Configuring security with the projector Use of security type WEP Use of security type WPA-PSK, WPA2-PSK Available PSK key characters Easy wireless setting Setting ProceduresEasy wireless setting Wireless factory default Computer environment and Wireless LAN connection WIRELESS indicator display WIRELESS indicator display Wireless LAN factory default settings Selected LAN 6. Basic setting and operation Starting up the Browser Select a display mode and loginChapter 6 Basic setting and operation STANDARD MODE Setting page Display of main setting pagezMain setting page in the Standard Mode display Starting up the browser Example of the Setting Page How to use the setting pagexMain setting page in the Light Mode display Setting Pallet Text box setting Type of the setting palletHow to use the setting page Pull-downmenu setting Password for PJLink function Initial settingSwitches PJLink password authentication on or off Japanese Initial setting Network PIN code settingPJLink and password setting Whats PJLink? Date and time setting Auto settingManual setting Network configuration Setting of LANNetwork configuration 3.After completing the network configuration, press Regist button to register the network information. The SimpleWireless setting is fixed, which cannot be changed from factory default value Description Configuring wireless LAN settingItem WPA-PSKand WPA2-PSKmode are not available Configuring wireless LAN security setting Notes for entering characters E-mailsetting E-mailsetting1Setting SMTP server and administrator address Administrator 2Registering and deleting E-mailaddresses 3Option selection for sending alert mail Examples: Type and contents of alert mail When internal PJ temperature is too highWhen internal PJ power circuit is failed When PJ lamp replacement time is reached Enter user name of the projector etc. optional SNMP settingSNMP setting Enter place of the projector optional Check and delete the trap address publicUp to 10 trap addresses can be registered Trap option setting Chapter 6 Basic setting and operation 7. Controlling the projector PJ status Power control and status checkChapter 7 Controlling the projector PJ temp Power control and status check 1.Select “Setting” from the Projector menuAbout projector condition Controls Input Available selection at the Component input SystemAvailable selection at the RGB input Controls Image mode Image adjustmentInput source Video Computer Sound Adjusts the sound volume from the speakersSuppresses the sound PC adjustment table below Setting up the projectorSetting up the projector Screen mode Item Lamp counter resetting To set the timer event on specified date Timer settingHow to set the timer 1Set a day or date Change the event mode Check the timer eventsTimer setting 2Set an execute time Event Notes on timer settingProjector Power Event Displays selected signal system Projector informationProjector information Input signal status Timer has been set Indication of the lamp statusDisplays the timer setting status No timer setting Example of multi control Controlling and setting the multi-projectorsMulti-control Multi-control Multi control setting Start/stop the multi control Enter projector name or installed location etc Register the projectorConfirmation of registered projector Enter IP address of the projector to control Change the mode of the registered projector StatusMode Controlling all together Setting all togetherCheck & Change page in the light mode Check & Change page in the light mode Viewer auto setting all together 8. Network capture functions Real Time Capture Network CommunicationModerator Function Real Time Capture +p.89 About Network Capture functionStart up the Network Capture Network Communication +p.94 Menu during Real time capturing Commands on the task barAbout Network Capture function Menu during Moderator function Parameter set up Using the Real Time Capture Using the Real Time CaptureRegistering the computers 1 Control by the computer Using the real time capture 2 Control by the web browser 3 Control by the projector 4 Control by the computer with USB memory Using the Network Communication Settings before using the Network Communication Using the Network Communication Menu Menu treeDescription of capture editing window Submenu Bar of Main PC Command ToolTool bar button names tool bar Start the communication How to use the Network communicationHow to acquire and release the editing authority Join the communication only for Sub PC Edit capture image Setting of the drawing tool attributeHow to use the Network communication Drawing figures Letter attribute setting Drawing letter Operation on the Main PC PreparationOn the Communication Operation on the Sub PC Executing the forcing mode Moderator Moderator functionModerator function Clients Preparation for using the moderator function Normal mode application windowModerator mode application window Moderator operation Using the moderator functionDescription of application window Client operation Moderators password setting up Unregister moderator status Error messages Error informationError information Cause and corresponding Chapter 8 Network capture functions 9. Network Viewer functions Start up and quit the File Converter 1 How to use the Network Viewer 5 File ConverterCreating the available data Network Viewer Chapter 9 Network Viewer functions Menu Tree Command Tool ButtonCreating the available data Sub Menu 2 When converting each file, select a preview image first and then click Convert each file Conversion mode Setting of output destination and conversion modeOutput destination Folder 2 How to use the Network Viewer 5 File Converter Procedure of making program Creating a program file Program EditorCreating a program file Program Editor 4 Click New button 1 Select a folder list contains images to change Image frame on the index window Example of the created program selection The limitation of the Program file Using the Network Viewer function 1 Control by the web browserCondition to use the Network Viewer function 1 IMPORTANT NOTICE 2 Setup the setting page 1 of the Visual displayUsing the network viewer function Enter your login account of the FTP server Decides a image to Switches to the List modeSwitches to the thumbnail mode start auto display with 4 Auto Display setting and control page Description Error information2Control by the projector Error type Times Display time Repeat timesDisplay time of the image 3 to 240 sec Auto Chapter 9 Network Viewer functions Use of telnet Web browser setting Firewall setting Troubleshooting Terminology10. Appendix Use of telnet ControlChapter 10 Appendix Command list table Use of telnet Flash Player enable Web browser settingActive Script/JavaScript enable Proxy setting Web browser setting ActiveScript settingFlash Player enable ActiveX controls and plug-inssetting Using proxy server Proxy settingFlash Player Add-onsetting Not using proxy server JavaScript Setting Flash Player Plug-insettingNetscape Navigator Not using proxy server Firewall setting Firewall setting Wireless LAN TroubleshootingThe computer cannot connect projectors Wired LAN Wireless LAN Connection cannot be established Troubleshooting Infrastructure ModeCannot start up the browser Network capture Cannot be turned on/off with the web browser Speed of playing back images are very slow I cannot make a new program file Network ViewerFile Converter What kind of image formats can I convert? Troubleshooting WEP Wired Equivalent Privacy DHCP server Dynamic Host Configuration ProtocolESSID Extended Service Set Identifier Wi-Fithe Standard for Wireless Fidelity Terminology SO-WIN-KV7A SANYO Electric Co., Ltd

Indication of the lamp status

Icon display/background

Lamp Corres.

lamp.

Displays the use time of the filter.

Displays the timer setting status.

Timer has been set.

No timer setting.