107 | Sanyo POA-LN02 specification

Q&A

Q&A

Installation/Access

QWhy doesn’t the setting page appear in my web browser?

AFollowing causes are possible. Please check them.

1.The monitor does not connect to the network. Check LED indicators status ( p.17).

-Check the connection of LAN cable if the LINK indicator does not illuminate red.

-Check the network configuration of the monitor if ACT indicator does not illuminate green.

2.Wrong network configuration of the monitor

Check the network configuration of the monitor ( p.37).

3.Wrong network configuration of the computer. Check the network configuration of the computer.

4.The network unit is used with the default setting ( p.21).

5.The proxy setting of the web browser is not set correctly ( p.100).

6.The computer does not provide TCP/IP protocol.

QNo setting page in my web browser? Is the problem in the network or in the monitor? I would like to find out the problem whether it is in the net- work or in the monitor

ACheck it by the following steps

1.Disconnect the monitor from the network and connect the monitor and com- puter with the UTP cross cable directly.

2.Change network configuration of the computer and monitor as shown in the example below.

(Monitor setting)		(Computer setting)
IP Address	: 192.168.0.2	IP Address	: 192.168.0.5
Subnet Mask	: 255.255.255.0	Subnet Mask	: 255.255.255.0
Default gateway	: 0.0.0.0	Default gateway	: (blank)
DNS	: 0.0.0.0	DNS	: (blank)

LD-NET ORGANIZER OWNER'S MANUAL

107

Image 107

Sanyo POA-LN02 owner manual 107, Why doesn’t the setting page appear in my web browser?

Contents

LD-Net Organizer POA-LN02 Address ComplianceFederal Communication Commission Notice Model Numbers POA-LN02 Trade Name Sanyo Responsible party Compliance and Caution Contents Appendix Network ViewerPage Chapter Features Web Management function p.45 Multi-control function p.59 Operating environment of LD-Net Organizer Network unit Quick Setup GuideBefore use Package contains Trademarks Expression/AbbreviationUse of this manual Preparation Installation Set up is complete Flow of installationInstallation and network configuration p.18-25 Installation of the software p.26-28 Name and function of each part Mounting Installation and network configuration Installation and network configuration Connection of LAN cable Configure the network with computer Network configurationProcedure of Connecting the monitor to the network As follows and restart the computer Configure the network with the computerDefault network configuration is set as follows Completing of installation Configure the network of computer Network PIN code setting Set the supplied Network Viewer & Capture Installing the softwareNetwork Viewer & Capture 3 installation Network Viewer 3 File Converter Installed softwareFollowing 3 software are installed on your computer Network Capture Installed software and places File Converter 2 Installation Basic Setting and Operation Entering User Name must be user and it can not be changed Login the setting page of the monitorSelect a display mode and login Enter the IP address Main setting page in the Standard Mode display Display of main setting Set button How to use the settingMain setting page in the Light Mode display Example of the Setting Radio button setting Type of the setting palletText box setting Pull-down menu setting Description Initial settingUse of Battery Initial setting Manual setting Date and time settingAuto setting Sets IP address of the monitor Network configuration Setting Smtp server and administrator address Mail setting Addresses are listed as the figure on the right Is turned off except Power/Fan fail, High Temp, Power saveRegistering and deleting E-mail addresses Option selection for sending alert mail Examples Type and contents of alert mail When the signal is interrupted When panel usage time reaches hoursWhen power save function turns Monitor off Community Snmp settingEnter user name of the monitor etc. optional Enter place of the monitor optional Up to 10 trap addresses can be registered Check and delete the trap addressTrap Item Description Trap option Trap option setting Controlling the Monitor Description Monitor status Power control and status check Power control and status check Input Selects input mode of the monitorSelects signal source of the input Controls This function is to adjust the displayed picture image Picture adjustment Suppresses the sound. ON, OFF Adjusts the sound volumeSound PC adjustment Input mode Setting up the monitorSwitches the screen mode. Full, Zoom169 There may not be available mode depending on Sets the image to freeze mode.ON, OFF Sets remote control inhibition mode. ON, OFFThis function is not effective for the settings Mail settings, etc Sets to divide the vertical picture Sets tile mode active. Off, OnAdjusts the vertical picture for smooth image Sets to divide the horizontal picture Set a day or date Timer settingHow to set the timer Select an event action Check the timer eventsChange the event mode Set an execute time Time Items Description Monitor information Example of multi control Controlling and setting the multi-monitorsMulti-control Start/stop the multi control Multi control setting Confirmation of registered monitor Register the monitor Indications Change the mode of the registered monitorMode Operation Status Controlling all together Check & Change page in the light modeSetting all together Viewer auto setting all together Network Capture Real Time Capture p.68 Commands on the task barAbout Network Capture function Launching the Network Capture About Image Quality Parameter set upClick Network Capture 3 icon on the task bar Up to 30 computers can be registered Using the Real Time CaptureRegistering the computers Control by the computer Select input mode to Network previously Start capturing of the PC1 from the PC5 Control by the web browser Using the Network Communication Settings before using the Network Communication Menu tree Description of capture editing window Bar of Sub PC Command Tool SaveCommand Tool Tool bar button names How to use the Network Communication Erase drawn object Setting of the drawing tool attributeEdit capture image Drawing figures Drawing letter Letter attribute setting On the Communication Network Communication operation and change of statePreparation Quits the communication forcibly Executing the forcing modeReleases the editing authority forcibly Error messages Network Viewer File Converter 1 window How to use the Network Viewer 3 File ConverterCreating the available data Network Viewer Launch and quit the File Converter Menu Sub Menu Description Update Updates contents of the preview windowCreate the available data Menu Tree Network Viewer Folder Setting of output destination and conversion modeConversion mode Output destination Select a folder and click Save button Open a document with the individual software Specify the root directory of the FTP server. Normally use Procedure of making programCreating a program file Program Editor Enter the FTP server name or IP address Moves down the selected folder path Displays the folder selection windowDeletes the folder path from the folder list Moves up the selected folder path Setting up the display order and time of the images Shows that the image in the folder is unchanged Image frame on the index windowBlue frame Red frame Limitation of the Program file This function is not available in the light modeExample of the created program selection Condition to use the Network Viewer function Using the Network Viewer functionUsed when using the network capture function Setup the setting page 2 of Selection display setting Setup the setting page 1 of Image display setting Auto display function Switches to the List modeSwitches to the thumbnail mode Steps down the startup image Auto Display setting and control Error type Description Error information Appendix To another network Examples of connectionPeer-To-Peer connection Entrance hall Gateway Router installed in the network Proxy setting Web browser settingActive Script/JavaScript enable Flash Player enable 101 ActiveX controls and plug-ins settingExamples OS/Browsers Windows XP Professional 102 Flash Player Add-on settingUsing proxy server Not using proxy server Netscape Navigator 103 104 105 Product specification 106 Port specificationPin modular connector RJ-45 Following causes are possible. Please check them Why doesn’t the setting page appear in my web browser?107 108 How can I restrict access from the computer How many monitors can I control with multi-control function? 109 You can register up to 10 addresses 110 111 Why am I not receiving E-mail alert messages? 112 Can I update the firmware of the network unit MAC address is indicated on the case back as the below What is the MAC address assigned to the network unit?113 What are the rules for IP address assignment? Cannot make a new program file Why doesn’t the computer screen appear on the monitor?114 Images from the file server don’t appear on the monitor? Bitmap format .bmp Jpeg format .jpeg .jpg Microsoft power point format .ppt115 What kind of image formats can I convert? Ifkm