Compliance, Address, Telephone No 818998-7322 | Sanyo POA-LN02

FOR HOME OR OFFICE USE

POA-LN02

Tested To Comply

With FCC Standards

Compliance

Federal Communication Commission Notice

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to SANYO part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment gener- ates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or televi- sion reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Numbers	: POA-LN02
Trade Name	: Sanyo
Responsible party	: SANYO FISHER COMPANY
Address	: 21605 Plummer Street, Chatsworth, California 91311
Telephone No.	: (818)998-7322

Image 2

Sanyo POA-LN02 owner manual Compliance, Federal Communication Commission Notice, Address, Telephone No 818998-7322

Contents

POA-LN02 LD-Net Organizer Model Numbers POA-LN02 Trade Name Sanyo Responsible party ComplianceFederal Communication Commission Notice Address Compliance and Caution Contents Network Viewer AppendixPage Chapter Features Web Management function p.45 Multi-control function p.59 Operating environment of LD-Net Organizer Package contains Quick Setup GuideBefore use Network unit Trademarks Expression/AbbreviationUse of this manual Preparation Installation Installation of the software p.26-28 Flow of installationInstallation and network configuration p.18-25 Set up is complete Name and function of each part Installation and network configuration Mounting Installation and network configuration Connection of LAN cable Configure the network with computer Network configurationProcedure of Connecting the monitor to the network As follows and restart the computer Configure the network with the computerDefault network configuration is set as follows Completing of installation Configure the network of computer Network PIN code setting Set the supplied Network Viewer & Capture Installing the softwareNetwork Viewer & Capture 3 installation Network Capture Installed softwareFollowing 3 software are installed on your computer Network Viewer 3 File Converter File Converter 2 Installation Installed software and places Basic Setting and Operation Enter the IP address Login the setting page of the monitorSelect a display mode and login Entering User Name must be user and it can not be changed Display of main setting Main setting page in the Standard Mode display Example of the Setting How to use the settingMain setting page in the Light Mode display Set button Pull-down menu setting Type of the setting palletText box setting Radio button setting Description Initial settingUse of Battery Initial setting Manual setting Date and time settingAuto setting Network configuration Sets IP address of the monitor Mail setting Setting Smtp server and administrator address Option selection for sending alert mail Is turned off except Power/Fan fail, High Temp, Power saveRegistering and deleting E-mail addresses Addresses are listed as the figure on the right Examples Type and contents of alert mail When the signal is interrupted When panel usage time reaches hoursWhen power save function turns Monitor off Enter place of the monitor optional Snmp settingEnter user name of the monitor etc. optional Community Item Description Check and delete the trap addressTrap Up to 10 trap addresses can be registered Trap option setting Trap option Controlling the Monitor Power control and status check Description Monitor status Power control and status check Controls Selects input mode of the monitorSelects signal source of the input Input Picture adjustment This function is to adjust the displayed picture image Suppresses the sound. ON, OFF Adjusts the sound volumeSound PC adjustment There may not be available mode depending on Setting up the monitorSwitches the screen mode. Full, Zoom169 Input mode Mail settings, etc Sets remote control inhibition mode. ON, OFFThis function is not effective for the settings Sets the image to freeze mode.ON, OFF Sets to divide the horizontal picture Sets tile mode active. Off, OnAdjusts the vertical picture for smooth image Sets to divide the vertical picture Set a day or date Timer settingHow to set the timer Set an execute time Check the timer eventsChange the event mode Select an event action Time Monitor information Items Description Example of multi control Controlling and setting the multi-monitorsMulti-control Multi control setting Start/stop the multi control Register the monitor Confirmation of registered monitor Status Change the mode of the registered monitorMode Operation Indications Controlling all together Check & Change page in the light modeSetting all together Viewer auto setting all together Network Capture Launching the Network Capture Commands on the task barAbout Network Capture function Real Time Capture p.68 About Image Quality Parameter set upClick Network Capture 3 icon on the task bar Up to 30 computers can be registered Using the Real Time CaptureRegistering the computers Select input mode to Network previously Control by the computer Control by the web browser Start capturing of the PC1 from the PC5 Using the Network Communication Settings before using the Network Communication Description of capture editing window Menu tree Tool bar button names Command Tool SaveCommand Tool Bar of Sub PC How to use the Network Communication Drawing figures Setting of the drawing tool attributeEdit capture image Erase drawn object Letter attribute setting Drawing letter On the Communication Network Communication operation and change of statePreparation Quits the communication forcibly Executing the forcing modeReleases the editing authority forcibly Error messages Network Viewer Launch and quit the File Converter How to use the Network Viewer 3 File ConverterCreating the available data Network Viewer File Converter 1 window Menu Tree Update Updates contents of the preview windowCreate the available data Menu Sub Menu Description Network Viewer Output destination Setting of output destination and conversion modeConversion mode Folder Open a document with the individual software Select a folder and click Save button Enter the FTP server name or IP address Procedure of making programCreating a program file Program Editor Specify the root directory of the FTP server. Normally use Moves up the selected folder path Displays the folder selection windowDeletes the folder path from the folder list Moves down the selected folder path Setting up the display order and time of the images Red frame Image frame on the index windowBlue frame Shows that the image in the folder is unchanged Limitation of the Program file This function is not available in the light modeExample of the created program selection Condition to use the Network Viewer function Using the Network Viewer functionUsed when using the network capture function Setup the setting page 1 of Image display setting Setup the setting page 2 of Selection display setting Steps down the startup image Switches to the List modeSwitches to the thumbnail mode Auto display function Auto Display setting and control Error information Error type Description Appendix To another network Examples of connectionPeer-To-Peer connection Gateway Router installed in the network Entrance hall Flash Player enable Web browser settingActive Script/JavaScript enable Proxy setting Windows XP Professional ActiveX controls and plug-ins settingExamples OS/Browsers 101 Not using proxy server Flash Player Add-on settingUsing proxy server 102 103 Netscape Navigator 104 Product specification 105 106 Port specificationPin modular connector RJ-45 Following causes are possible. Please check them Why doesn’t the setting page appear in my web browser?107 How can I restrict access from the computer 108 109 How many monitors can I control with multi-control function? 110 You can register up to 10 addresses Why am I not receiving E-mail alert messages? 111 Can I update the firmware of the network unit 112 What are the rules for IP address assignment? What is the MAC address assigned to the network unit?113 MAC address is indicated on the case back as the below Images from the file server don’t appear on the monitor? Why doesn’t the computer screen appear on the monitor?114 Cannot make a new program file What kind of image formats can I convert? Microsoft power point format .ppt115 Bitmap format .bmp Jpeg format .jpeg .jpg Ifkm