2ELEVATIONHANDWHEEL...elevatesorlowersthe bladeTurnclockwiseto. elevate... counterclockwise tolower,
3 TILT HANDWHEEL... tilts the bladefor bevel
'cutting. Turn clockwiseto tilt towardleft ...
counterclockwise to tilt toward right,
When the blade is tilted to the LEFT as far as it will go, it should be at 45 ° to the table and the bevel pointer should point 45 ° .
NOTE: There are LIMIT STOPS inside the saw which
prevent the | blade from tilting beyond 45 ° to the LEFT | ||
and 90 | ° to | the RIGHT. (See "Adjustments" | section |
"Blade | Tilt, | or Squareness of Blade to Table"), |
|
Select a suitable piece of smooth straight wood.., drill two holes through it and attach it with screws.
NOTE; When bevel crosscutting, attach facing so that it extends to the right of the miter gauge and use the miter gauge in the groove to the right of the blade.
4 TILT LOCK HANDLE ... locks the blade in the
desired tilt position. To loosen, turn counterclockwise, Push handle in and turn it to another position if necessary in order to tighten or loosen.
5RIP FENCE .. is locked in place by tightening the lock knob. To move the fence, loosen the knob and grasp the fence with one hand at the front.
Holes are provided in the rip fence for attaching a wood facing when using the dado head, or molding head.
Select a piece of smooth straight wood approx. 3/4 in.
thick and the same size as the rip fence.
Attach it to the fence with three Round Head ##10
Wood Screws 2 in. long. To remove the facing, loosen the screws, slide the facing forward and pull the screws through the round holes.
WOOD FACING
\
\\ ROUND HEAD ///
#!0 WOOD SCREWS
6 MITER GAUGE ... head is locked in position for
crosscutting or mitering by tightening the lock knob.
ALWAYS LOCK IT SECURELY WHEN NUSE.
There are two slots for the stop pin at the 45 degree right and left positions for conveniently setting the Vliter Gauge to cut miters.
NOTE: The slots for the stop pin and the graduations are manufactured to very close tolerances which
provide accuracy for average woodworking. In some caseswhere extreme accuracy is required, when making angle cuts, for example, make a trial cut and then
recheck it.
If necessary, the miter gauge head can then be swiveled slightly to compensate and then locked.
Slots are provided in the miter gauge for attaching an
AUXILIARY FACING to make it easier to cut long p=eces. Be positive facing does not interfere with the proper operation of the sawblade guard.
|
| AUXIELIARY FACING |
STOP PIN | 45 ° SLOT "\ |
|
| FOR STOP PIN | \ |
|
|
BLADEGUARD must always be in place and working properly for all
whereby the blade cuts completely through the workpiece.
To remove the guard for special operations, loosen the thumbscrew and slide the guard off of the rod. DO NOT DISTURB THE SETTING OF THE ROD.
When replacing the guard, make sure the PIN in the rod engageswith the NOTCH in the spreader support, Make
sure thumbscrew is tightened securely,
8TABLE INSERT is removable for removing or installing blades or other cutting tools.
/
SCREW
WARNING: FOR YOUR OWN SAFETY, TURN
SWITCH "OFF" AND REMOVE PL.UG FROM
POWER SOURCE OUTLET BEFORE REMOVING INSERT.
A, Lower the blade below the table surface.
B.Raise blade guard.
C.Loosen Screw.
D.Lift in_ert from front end, and pull toward front of saw.
NEVER OPERATE THE SAW WITHOUT THE PROPER INSERT IN PLACE. USE THE SAW BLADE
INSERT WHEN SAWING . . . USE THE
COMBINATION DADO MOLDING INSERT WHEN DADOING OR MOLDING.
21
