R. DO NOT remove small ;)ieces of cut-off material
that may become trapped inside the blade guard while the saw is running. This could endanger your
hands or cause a kickback. Turn saw "OFF" and wait until blade stops.
S.Use extr_ care when ripping wood that has a twisted
grain or is twisted or bowed it may rock on the table and/or pinch the sawblade.
10.KNOW YOUR CUTTING TOOLS
ADull, gummy, or improperly sharpened or set cutting tools can cause material to stick, jam, stall the saw, or kickback at the operator.
Minimize potent/a injury by proper cutting tool and machine maintenance.
NEVER ATTEMPT TO FREE A STALLED
SAWBLADE WITHOUT FIRST TURNING THE SAW OFF
B, Never use grinding wheels, abrasive
11. USE ONLY ACCESSORIES DESIGNED FOR THIS
SAW
12.Crosscutting operations are more conveniently worked
and with greater safety if an auxiliary wood facing is attached to the miter gauge using the holes provided
However, the facing must notinterfere with the proper
functioning of the sawblade guard.
13.Make sure the top of the arbor or cutting tool rotates
toward you when standing in normal operating
position. Also make sure the cutting tool, arbor collars
and arbor nut are installed properly. Keep the cutting
tool as low as possible for the operation being
performed. Keep all guards in place whenever possible,
14.Do not use any blade or other cutting tool marked for
an operating speed less than 3450 RPM. Never use cutting tool larger in diameter than the diameter for which the saw was designed. For greatest safety and
efficiency when ripping, use the maximum diameter blade for which the saw is designed, since under these conditions the spreader is nearest the blade.
15.AcIjust table inserts flush with the table top. NEVER operate the saw unlessthe proper insert is installed.
16, NEVER feed material into the cutting tool from the rear of the saw. An accident and serious injury could
result.
17.THINK SAFETY.
Safety m a combination of operator common sense and alertness at all times when the saw is being used.
18.NOTE AND FOLLOW SAFETY INSTRUCTIONS THAT APPEAR ON THE FRONT OF YOUR SAW.
DANGER
FOR YOUR OWN SAFETY
READ AND UNDERSTAND OWNER'S MANUAL
BEFORE OPERATING MACHINE:
1WEAR SAFETY GOGGLES PER ANSI Z87.1 AT ALL TIMES
2.USE
4, USE A
6DO NOT PERFORM OPERATIONS "FREEHAND"
7, NEVER REACH AROUND OR OVER SAW BLADE
19.WARNING: DO NOT ALLOW FAMILIARITY (GAINED FROM FREQUENT USE OF YOUR SAW)
TO BECOME COMMONPLACE.ALWAYS REMEMBER THAT A CARELESS FRACTION OF A
SECOND IS SUFFICIENT TO INFLICT SEVERE INJURY.
20.WARNING: THE
THE BLADE AT APPROXIMATELY 3450 RPM
WHEN USED WITH A 3450 RPM MOTOR. NEVER SUBSTITUTE THESE PULLEYS TO INCREASE THIS SPEED BECAUSE IT COULD BE DANGEROUS.
The operation of any power tool can result in foreign objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles complying with ANSI Z87.1 (shown on Package) before commencing
power too] operation. Safety Goggles are available at Sears retail or catalog stores.
MOTOR SPECIFICATIONS AND
This saw is designed to use a 3450 RPM motor only. Do not use any motor that runs faster than 3450 RPM. It is wired for operation on
IT MUST NOT BE CONVERTED TO OPERATE ON 230
VOLTS. EVEN THOUGH SOME OF THE
RECOMMENDED MOTORS ARE DUAL VOLTAGE. Changing to _0 volt will not conserve energy and requlrcs changing the power cord plug.
The outlet in the switch box will accept either a 15 an"_. or a 20 amp. motor plug.
RECOMMENDED | CRAFTSMAN | MOTORS | FOR USE ON |
THIS SAW. |
|
|
|
H.P. | R.P.M. | Volts | Catalog No. |
1 | 3450 | 11_120 | 1217 |
1 | 3450 |
| 1220 |
CAUTION: Do not use blower or washing machine motors or any motor with an automatic reset overload protector as their use may be hazardous.
ELECTRICAL REQUIREMENTS
CONNECTIN G TO POWER SOURCE OUTLET
This saw must be grounded while in use to protect the operator from electrical shock.
If power cord is worn or cut, or damaged in any way, have it replaced immediately.
If your saw is for use on less than 150 volts it has _ l_lug that looks like below.
\
GROUNDING PRONG
_" PROPERLY GROUNDED
