Open the lower side cover | Sharp AL-1644, AL-1633 specification

TROUBLESHOOTING

MISFEED IN THE LOWER PAPER TRAY (Two-tray model only)

Note	Make sure that there is no misfed paper in the tray before pulling it out. (p.56)

1 Open the lower side cover.

Grasp the handle to open the lower side cover.

5 Close the lower paper tray.

2 Remove the misfed paper.

Be careful not to tear the misfed paper during removal.

3 If the misfed paper is not seen in step 2, lift and pull out the lower paper tray and remove the misfed paper.

Be careful not to tear the misfed paper during removal.

4 Close the lower side cover.

The misfeed indicator ( ) will go out.

If the misfeed indicator ( ) does not stop

Note	blinking, check for torn pieces of paper in the
	blinking, check for torn pieces of paper in the
	machine.

Page 62

Image 62

Sharp AL-1644 Open the lower side cover, Close the lower paper tray Remove the misfed paper, Close the lower side cover

Contents

AL-1633 AL-1644Page Contents Troubleshooting Misfeed in the SPF only on the SPF model Changes, e.g., near an Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Air conditioner or Trademark acknowledgements Software Setup Guide separate manual Using the ManualOnline Manual on the accessory CD-ROM Environmental Information This manual covers the following models Conventions Used in this ManualSPF Differences Between Models Model AL-1644 AL-1633 Appearance Main Features Part Names and Functions Parallel port Fusing unit release leversFusing unit paper guide Open to remove misfed paper Document feeder tray Operation Panel SPF indicator only on the SPF model Original Size Enter key Enter / Original Size indicatorsPaper Size indicators Auto Image key Auto % / indicator Checking Packed Components and Accessories Unpacking SET-UP Install the TD cartridgeFor installation of the TD cartridge, see the next Gently lift and pull out the paper tray until it stops Close the front cover Installing the TD CartridgeTD cartridge replacement required indicator will go out Power OFF Power on and OFFPower on Power Save Modes Paper Paper tray type Paper type Size Weight CapacityLoading Paper Special papers Locks in place Loading PaperLoading the paper tray Fan the paper Unfold the bypass tray Important points when inserting paper in the bypass trayLoading the bypass tray Set the paper guides to the copy paper width Changing a TRAY’S Paper Size Setting Envelopes Important points when using the printer mode Press the Start key and then press the Paper Size Enter key Open the document cover/SPF, and place the original Normal CopyingCopying from the document glass Set the number of copies Copying from the SPF only on the SPF modelSet the originals face up in the document feeder tray Auto paper select mode Two-tray model only Selecting the Tray Auto tray switching Two-tray model onlyMaking a Copy Darker or Lighter Original types Automatic Ratio Selection Setting the Number of CopiesREDUCTION/ENLAREGMENT/ZOOM Original position Selectable ratios Manual Ratio Selection Selecting a preset ratioFine adjustment of the ratio Press the Auto Image key Auto % XY Zoom copying Press the Copy ratio display key Down the Copy ratio display key Place original B as shown below TWO-SIDED Copying Using the Bypass TrayCopy original a Dual page Copying Replace the previous originals and press the Start key Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Make sure that paper is loaded in the tray Using the Printer ModeBasic Procedure for Printing Click the Print button or the OK button to begin printing Pausing a print job Using the Scanner ModeScanning Using the Keys on the Machine When Use close paper size is disabled Press a Scan Menu key to begin Scanning from Your ComputerScan Menu keys and the Button Manager scan menu Scanning Printer During printing Operation in COPY, PRINTER, and Scanner ModesDuring copying Scanner During scan preview Adjusting the Automatic Exposure Level Photo indicator stops blinking and lights steadily Enabling Toner Save ModeWhen enabling toner Save mode, make sure Customising Settings User Programs Minimum Explanation300dpi Short beep Selecting a Setting for a User Program Base settings Auditing Mode Settings Settings for Auditing ModeAuditing Mode Factory default settings Selecting Auditing Mode Settings For the setting codes, see Auditing Mode SETTINGS. p.41 Account number change Auditing modeAccount number entry Account number deletion Resetting account Copying when Auditing mode is enabled Troubleshooting MACHINE/COPYING Problems Pieces of paper inside machine Problem Cause and solution Misfeed occursPaper is not loaded properly Paper misfeed Too much paper is loaded in the tray Power Save indicator is only lit Lit Any other indicators are litPower Save indicator is Original smudged or blotchy Printing and Scanning Problems Runs off the paper UnevenPrinted image is dirty Original is smudged or blotchy You have not specified a suitable resolutionBrightness and contrast settings are not suitable Poor scanning quality Click Add or Remove Programs Removing the softwareClick the start button, and then click Control Panel If you need to remove the software, follow these steps Indicators and Display Messages AL-1644 AL-1633 Misfeed RemovalRemove the misfed original Misfeed indicator will go out Misfeed in the Bypass Tray Misfeed in the Machine Misfeed in the paper feed area Misfed paper during Misfeed in the fusing areaAllow easier removal Be careful not to tear the misfed paper during removal Misfeed in the transport areaClose the side cover Push the upper paper tray in completely Misfeed in the Upper Paper TrayClose the upper paper tray Close the lower side cover Open the lower side coverClose the lower paper tray Remove the misfed paper Grasp the handle to open the lower side cover Replacing the TD Cartridge Replacing the Drum Cartridge Drum cartridge replacement required Indicator will go out Total output count Checking the Total Output CountChecking the Total Output Count Total copy count Press the Light key to return to the normal display Checking the Toner Level and Drum Cartridge LifeToner Level Hold down the Clear key for more than 5 seconds Cleaning the Bypass Tray Paper Feed Roller Routine MaintenanceCleaning the Document Glass and SPF/ Document Cover Cleaning the Transfer Charger Proper Storage Storage of SuppliesSupply Part Numbers Supply list Moving Instructions Accessories p.12When moving this machine, follow the procedure below Specifications SPF only on the SPF model Specifications Printer Function Scanner Function Software License Page Symbols Index Printing and scanning problems TD cartridge replacement requiredTray Select key 11, 19, 21, 23 Troubleshooting Normal copying Indicators, lit and blinking Machine settingsProblem occurs Memo Memo Class Laser Product Laser Klasse Page 2004E