Misfeed in the Upper Paper Tray

TROUBLESHOOTING

Note	Make sure that there is no misfed paper in the tray before pulling it out. (p.56)

1 Lift and pull out the upper paper tray and remove the misfed paper.

Be careful not to tear the misfed paper during removal.

2 Open and close the side cover.

The misfeed indicator ( ) will go out.

•	When closing the side cover, press on the	5
Note	handle.	5

•If the misfeed indicator ( ) does not stop blinking, check for torn pieces of paper in the machine.

3 Close the upper paper tray.

Push the upper paper tray in completely.

Page 61

Image 61

Sharp AL-1633 Misfeed in the Upper Paper Tray, Close the upper paper tray, Push the upper paper tray in completely

Contents

AL-1644 AL-1633Page Contents Misfeed in the SPF only on the SPF model Troubleshooting Do not install your machine in areas that are Important Points When Selecting AN Installation SiteChanges, e.g., near an Air conditioner or Trademark acknowledgements Online Manual on the accessory CD-ROM Using the ManualSoftware Setup Guide separate manual Environmental Information SPF Differences Between Models Conventions Used in this ManualThis manual covers the following models Model AL-1644 AL-1633 Appearance Main Features Part Names and Functions Fusing unit paper guide Open to remove misfed paper Fusing unit release leversParallel port Document feeder tray Operation Panel Paper Size indicators Original Size Enter key Enter / Original Size indicatorsSPF indicator only on the SPF model Auto Image key Auto % / indicator Unpacking Checking Packed Components and Accessories For installation of the TD cartridge, see the next Install the TD cartridgeSET-UP Gently lift and pull out the paper tray until it stops TD cartridge replacement required indicator will go out Installing the TD CartridgeClose the front cover Power on Power on and OFFPower OFF Power Save Modes Loading Paper Paper tray type Paper type Size Weight CapacityPaper Special papers Loading the paper tray Loading PaperLocks in place Fan the paper Loading the bypass tray Important points when inserting paper in the bypass trayUnfold the bypass tray Set the paper guides to the copy paper width Envelopes Changing a TRAY’S Paper Size Setting Press the Start key and then press the Paper Size Enter key Important points when using the printer mode Copying from the document glass Normal CopyingOpen the document cover/SPF, and place the original Set the originals face up in the document feeder tray Copying from the SPF only on the SPF modelSet the number of copies Auto paper select mode Two-tray model only Making a Copy Darker or Lighter Auto tray switching Two-tray model onlySelecting the Tray Original types REDUCTION/ENLAREGMENT/ZOOM Setting the Number of CopiesAutomatic Ratio Selection Original position Selectable ratios Fine adjustment of the ratio Selecting a preset ratioManual Ratio Selection Press the Auto Image key Auto % Press the Copy ratio display key XY Zoom copying Down the Copy ratio display key Copy original a TWO-SIDED Copying Using the Bypass TrayPlace original B as shown below Dual page Copying Press the Interrupt key to interrupt the copy run Interrupting a Copy RUNReplace the previous originals and press the Start key Basic Procedure for Printing Using the Printer ModeMake sure that paper is loaded in the tray Click the Print button or the OK button to begin printing Scanning Using the Keys on the Machine Using the Scanner ModePausing a print job When Use close paper size is disabled Scan Menu keys and the Button Manager scan menu Scanning from Your ComputerPress a Scan Menu key to begin Scanning During copying Operation in COPY, PRINTER, and Scanner ModesPrinter During printing Scanner During scan preview Adjusting the Automatic Exposure Level When enabling toner Enabling Toner Save ModePhoto indicator stops blinking and lights steadily Save mode, make sure User Programs Customising Settings 300dpi ExplanationMinimum Short beep Base settings Selecting a Setting for a User Program Auditing Mode Settings for Auditing ModeAuditing Mode Settings Factory default settings For the setting codes, see Auditing Mode SETTINGS. p.41 Selecting Auditing Mode Settings Account number entry Auditing modeAccount number change Account number deletion Copying when Auditing mode is enabled Resetting account Troubleshooting MACHINE/COPYING Problems Paper is not loaded properly Problem Cause and solution Misfeed occursPieces of paper inside machine Paper misfeed Too much paper is loaded in the tray Power Save indicator is Any other indicators are litPower Save indicator is only lit Lit Original smudged or blotchy Printing and Scanning Problems Printed image is dirty UnevenRuns off the paper Brightness and contrast settings are not suitable You have not specified a suitable resolutionOriginal is smudged or blotchy Poor scanning quality Click the start button, and then click Control Panel Removing the softwareClick Add or Remove Programs If you need to remove the software, follow these steps Indicators and Display Messages Remove the misfed original Misfeed RemovalAL-1644 AL-1633 Misfeed in the Bypass Tray Misfeed indicator will go out Misfeed in the paper feed area Misfeed in the Machine Allow easier removal Misfeed in the fusing areaMisfed paper during Close the side cover Misfeed in the transport areaBe careful not to tear the misfed paper during removal Close the upper paper tray Misfeed in the Upper Paper TrayPush the upper paper tray in completely Close the lower paper tray Remove the misfed paper Open the lower side coverClose the lower side cover Grasp the handle to open the lower side cover Replacing the TD Cartridge Replacing the Drum Cartridge Drum cartridge replacement required Indicator will go out Checking the Total Output Count Checking the Total Output CountTotal output count Total copy count Toner Level Checking the Toner Level and Drum Cartridge LifePress the Light key to return to the normal display Hold down the Clear key for more than 5 seconds Cleaning the Document Glass and SPF/ Document Cover Routine MaintenanceCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger Supply Part Numbers Storage of SuppliesProper Storage Supply list When moving this machine, follow the procedure below Accessories p.12Moving Instructions Specifications Printer Function SPF only on the SPF model Specifications Scanner Function Software License Page Index Symbols Tray Select key 11, 19, 21, 23 Troubleshooting TD cartridge replacement requiredPrinting and scanning problems Normal copying Problem occurs Machine settingsIndicators, lit and blinking Memo Memo Class Laser Product Laser Klasse Page 2004E

Sharp AL-1633, AL-1644 operation manual Misfeed in the Upper Paper Tray, Close the upper paper tray

Models: AL-1644 AL-1633

MISFEED IN THE UPPER PAPER TRAY

Be careful not to tear the misfed paper during removal.

The misfeed indicator ( ) will go out.

3 Close the upper paper tray.

Push the upper paper tray in completely.