Safety Precautions | Sharp AL-1650 guide

CAUTIONS

GETTING STARTED

Cautions

Follow the cautions below when using this copier.

●The fusing area is hot. Exercise care in this area when removing misfed paper.

●Do not look directly at the light source. Doing so may damage your eyes.

●The socket-outlet shall be installed near the equipment and shall be easily accessible.

●Place the copier on a firm, level surface.

● Do not install the copier in a humid or dusty location.

● When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.

●When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet.

●Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the copier.

SAFETY PRECAUTIONS

This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the copier does not produce hazardous laser radiation. For your safety, observe the precautions below.

●Do not remove the cabinet, operation panel or any other covers.

●The copier’s exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges or other items into switch slots.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure.

2

Image 4

Sharp AL-1650 operation manual Safety Precautions

Contents

AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions AUTO/MANUAL/PHOTO / / key and indicators p Original Size Enter key and indicators pPaper Size indicators Alarm indicators Dual page Copy key and indicator p Light and dark keys and indicatorsAuto Image key and indicator p @0 Preset Ratio selector keys and indicators p Copier Installation Do not install your copier in areas that are Getting Started Checking Packed Components and Accessories Unpacking SET-UP Install the TD cartridgeGently lift and pull out the paper tray until it stops Turn the power switch on Load copy paper SET-UPFront of the paper tray Store the pressure plate lock which has been removed Loading Copy Paper Push the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size 11ENTER key Using the SPF Turn the power switch onAdjust the copy density Normal Copying Set the number of copies using the two copy quantity Keys Stream feeding modeNormal Copying Press the Start key Using the original table Normal Copying REDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image Key Enter the number of copies Press the Start key REDUCTION/ENLARGEMENT/ZOOM Manual Bypass Feed special paper Unfold the bypass tray Bypass Feed special paper Press the Tray Select key to select the bypass TWO-SIDED Copying Press the XY-ZOOM key XY ZoomPress the copy ratio display Key XY Zoom Set the number of copies and press the Start key Reverse Press the B/W Reverse key Check the copy paper size Dual page Copy Press the Dual page Copy key Interrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and press Automatic Exposure Adjustment Press the AUTO/MANUAL/PHOTO Key To select the Manual Mode Toner Save ModeTo enter the toner save mode, press the light key TD Cartridge Replacement Genuine Supplies TD Cartridge Replacement Cartridge out until the green strap handle can be grasped To remove itBy the right hand. Lift the cartridge by the handle while Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridge Misfeed Removal Misfeed in the SPFFirst confirm the misfeed location Right feeding roller cover and remove the misfed Misfeed Removal Misfeed in the bypass trayMisfeed in the copier Gently pull the misfed paper out Removing it Fusing unit is hot. Take care in removing paperPush gently the right side of the front cover to open Cover Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paper Misfeed in the lower paper tray Misfeed in the upper paper trayClose the side cover by pressing the handle on the cover Remove the misfed paper Setting the user programs Enter a program number using the left copy quantity KeyUser Programs List of user programs Select the desired parameter using the right copy quantity User Programs Preheat mode Power Save ModesAuto power shut-off mode Setting the power save modes Power Save ModesCopying from the preheat mode User Maintenance Original table and document feeder coverBypass tray paper feed roller Transfer charger Charger cleaner out by holding the tab User MaintenanceGently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE? Copier TROUBLE? Self-diagnostic functionExample Supplies Types and sizes of copy paperSupply part numbers Supply list Supplies Genuine supplies statementProper storage Store copy paper in the wrapper and lying flat Moving Instructions Turn the power switch off and disconnect the power CordPush the paper tray back into the copier Specifications Copier Specifications Single Pass Feeder Index Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable Limits Other Limits Ingredients CAS No ProportionHealth Hazards None required under normal use Memo Memo Page Sharp Corporation