Sharp XG-P20XU 1 2, 3, 4, 1 2, 3, 4, 1 2, 3

E-37

Operation Buttons

Setting up GyroRemote

TEACH/LEARN

•Each GyroRemote has its own ID code, which must be recognized by the projector that is going to be used.

•The projector only recognizes the signal of the GyroRemote whose ID code has been input. Signals from other

projectors or GyroRemotes that may be operating in the same area are not allowed to interrupt each other.

Projector GyroRemote

On-screen Display

1Press LEARN on the projector.

2While “Do you want to LEARN?” is displaying, press

ENTER. You are now in LEARN mode.

CAUTION

•Entering LEARN mode erases all previously registered

GyroRemotes data. You must re-enter each GyroRemote ID code

in order for the projector to recognize them again.

3Press TEACH located on the front, inside the upper

cover on the remote within 5 minutes. “Register” will

appear on the display and you can now start using

the GyroRemote with the projector.

4To exit from the LEARN mode, press LEARN.

TEACH

LEARN

ENTER

Operating multiple projectors with one

GyroRemote

CAUTION

•Be aware that you can operate multiple projectors with one

GyroRemote, even if you are in another room, as long as you stay

within a 98 5 (30 m) range of the projector.

•LEARN mode will exit if the LEARN is pressed or 5 minutes has

elapsed.

1Set projector to LEARN mode.

2Press TEACH on the GyroRemote. You can now

operate multiple projectors with one GyroRemote.

3Perform steps 1 and 2 for each projector you plan to

use.

4To exit from LEARN mode, press LEARN.

•For setting multiple units in LEARN mode at one time, perform step

1 above for all projectors.

Using multiple GyroRemotes to operate one

projector

One projector can recognize up to 8 GyroRemote ID

codes.

1Set projector to LEARN mode.

2Press TEACH on all GyroRemotes being used. Once

the eighth GyroRemote is registered to operate one

projector, the LEARN mode automatically finishes.

You can now operate one projector using multiple

GyroRemotes.

3To exit from the LEARN mode, press LEARN.

•Contact your nearest Authorized Sharp Industrial LCD Products

Dealer or Service Center if you need to use an additional

GyroRemote unit.

Contents

Main E-1 Before using the LCD projector, please read this operation manual carefully. . WARNING: Introduction IMPORTANT SAFEGUARDS E-2 IMPORTANT SAFEGUARDS Caution Concerning the Lamp Replacement Cautions Concerning the Setup of the Projector Notes on Operation Caution Concerning the Lamp Unit IMPORTANT SAFEGUARDS Temperature Monitor Function Using the Carrying Handle Using the Kensington Lock Outstanding Features 1. High-end LCD Projector with Ultra High Brightness 2. Computer Compatibility 3. XGA Image Quality 4. Computer & Video Integrated Composer Technology Page Contents Important Information Introducing GyroRemote ..................... Image Projection .................................. Setting Up the Screen .......................... Basic Operation Maintenance & Troubleshooting Multiple Function Appendix How to Access the PDF Operation Manuals To Install Acrobat Reader from the CD-ROM For other operating systems: Accessing the PDF Manuals For other languages: Part Names GyroRemote Part Names Inserting and removing the batteries 1 42 3 Accessories Supplied Accessories Optional cables Page Projecting Computer Images Connecting the Projector to a Computer 12 Connecting to a computer using the standard 15-pin Input 1 2 1 2 3 4 2 Plug and Play function (when connecting to a 15-pin terminal) Page Watching Video Images 2 1 2 Watching Component Video Images 2 4 Example 1 Power ON/OFF Press POWER ON on the projector or POWER on the GyroRemote. Press POWER OFF on the projector or POWER on the GyroRemote. Setting Up the Screen Using the Adjustment Feet Using the Lens Shift LENS Button 1 2 3 4 Adjusting the Projection Distance Standard Setup (Front Projection) Throw Distance Upper and Lower Lens Shift Position Upper and Lower Lens Shift Position (Ceiling Mount) E-24 Standard Lens 1:1.8 to 2.4 l1(Max.) = (0.0482x0.0226) 3.28 l2(Min.) = (0.037x0.041) 3.28 l1(Max.) = (0.0525x0.0546) 3.28 l2(Min.) = (0.0404x0.0397) 3.28 E-25 AN-W6EZ 1:1.3 to 1.7 l1(Max.) = (0.0347x0.0709) 3.28 l2(Min.) = (0.0267x0.0715) 3.28 l1(Max.) = (0.0378x0.0726) 3.28 l2(Min.) = (0.0291x0.0731) 3.28 E-26 AN-T6EZ 1:2.5 to 3.3 l1(Max.) = (0.0674x0.178) 3.28 l2(Min.) = (0.0519x0.1829) 3.28 l1(Max.) = (0.0734x0.1764) 3.28 l2(Min.) = (0.0565x0.1778) 3.28 E-27 AN-P9MX 1:0.9 l= (0.0186x0.0563) 3.28 h = 0.3x l= (0.0203x0.0579) 3.28 h = 0.2451x E-28 AN-P48EZ 1:4.6 to 6.1 l1(Max.) = (0.1214x0.1272) 3.28 l2(Min.) = (0.0927x0.1233) 3.28 l1(Max.) = (0.1323x0.1272) 3.28 l2(Min.) = (0.101x0.1233) 3.28 Rear Projection Image Projection Projection Using a Mirror Ceiling-mount Projection Introducing GyroRemote GyroRemote Features Can operate one projector using multiple GyroRemotes. 1. RF Technology 2. Multi-Projector Control Can operate multiple projections with one GyroRemote. 3. Gesture tracking Projector Control Using GyroRemote All Button Assign selections Function ASSIGN 1 2 3 4 Using the Presentation Tools Button Assign list Stamp 1 2 3 4 Using lines 1 2 3 4 5 1 2 Using the mouse 1 2 Setting up GyroRemote Setting RF channels Confirming the present RF channel 1 2 1 2 3 4 Operating multiple projectors with one GyroRemote 1 2 3 4 Using multiple GyroRemotes to operate one projector 1 2 3 Setting up GyroRemote Turning off GyroRemote 1 2 Using as a Wired Remote Control Using the GyroRemote with a wired remote control cable Using the IR remote control as a wired remote Selecting the Input Signal Source Using the Operation Buttons Adjusting the Volume Muting the Sound Blacking out the Projected Image Superimposing a Black Screen sg Displaying a Still Image 1 2 Magnifying a Specific Portion of an Image 1 2 Pan Around the Screen 1 Adjusting the Picture Aspect Ratio Projector RESIZE UNDO 1 changes as shown below. Gamma Correction Function sss Gamma Modes 1 2 Using the GUI (Graphical User Interface) Menu Screen Basic Operations to can be operated from the projector or the GyroRemote with the following procedure. 1 2 Menu Bars Items on the INPUT 1, 2 or 3 Mode Menu Bar Main menu Sub menu Main menu E-46 Basic Operation Items on the INPUT 4 or 5 Mode Menu Bar Main menu Sub menu Main menu Adjusting the Picture for the procedure details. e. g. RGB input in INPUT 1 or 2 mode Adjusting the Color Temperature Selecting the Signal Type (RGB menu only) Progressive Mode for the procedure details. Adjusting the Computer Images (RGB menu only) Saving and Selecting Adjustment Settings Special Mode Adjustment Checking the Input Signal Auto Sync Adjustment Auto Sync Display Function Adjusting the Sound for the procedure details. Audio Out Speaker E-53 Displaying Dual Pictures (RGB menu only) for the procedure details. ) Reducing Image Noise (VIDEO menu only) for the procedure details. Setting the Video Signal (VIDEO menu only) Turning On/Off the On-screen Display Selecting a Background Image Selecting a Startup Image for the procedure details. Monitor Out/RS-232C Off Function Selecting the Economy Mode Automatic Power Shutoff Function Confirming the Lamp Usage Time Reversing/Inverting Projected Images Setting the Stacking Mode Locking the Operation Buttons on the Projector Deselecting Inputs Selecting the Transmission Speed (RS-232C) Controling Multiple Projectors with ID Numbers Setting the ID No. Protecting Important Settings with a Password Page Using Extended Functionality Features Internet access for self-diagnosis, status information and preventive maintenance LANLAN Internet LAN (RS-232C) Specifications and Command SettingsUsing Extended Functionality Features Multiple and group projector control via computer Using Extended Functionality Features E-65 Multiple Function , Deselecting Inputs. Simultaneous multiple projector control for stacking and videowall projection Using Extended Functionality Features E-66 Multiple Function Videowall Lamp/Maintenance Indicators Maintenance Indicators Lamp CAUTION 46 1 3 Remove the air filter. 5Replace the air filter. Turn off the power. 2Disconnect the power cord. Remove the bottom filter cover. 10 79 1 Resetting the lamp timer Replacing the Air Filter 46 1 3 Turn off the power and disconnect the power cord. 2Remove the bottom filter cover. Remove the air filter. Troubleshooting MENU For SHARP Assistance (U.S.A. only) Connecting Pin Assignments INPUT 1 RGB and OUTPUT (INPUT 1, 2) Signal Ports: 15-pin Mini D-sub female connector RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable INPUT 3 DVI Port: 29-pin E-73 (RS-232C) Specifications and Command Settings Return code (0DH) C1 C2 C3 C4 P1 P2 P3 P4 RABR 10_OK Command 4-digit Parameter 4-digit Response code format (RS-232C) Specifications and Command Settings PICTUREFINE SYNC E-75 (RS-232C) Specifications and Command Settings OPTIONS (2)LANGUAGE E-76 Wired Remote Control Terminal Specifications Specifications of wired remote control input Example of Reverse D to 3.5 mm minijack External: 5 V (1 A) Internal: GND Function and transmission codes Computer Compatibility Chart E-78 Dimensions Rear View Top View Side View Bottom View Units: inches (mm) Specifications Specifications are subject to change without notice. E-80 Glossary Index A B C D