Outline Gateway GW Unit, Input / Output Unit | SMC Networks EX500

EX500 Serial System

EX## - OME0008

1. Outline

A. Gateway ( GW ) Unit

( 1 ) The Gateway ( GW ) Unit can be connected with a PLC.

At present, Gateway ( GW ) Unit with the following communication protocols are available:

・Remote I/O ( RIO ) System slaves to Rockwell Automation PLC and SLC series unit.

・DeviceNet

・PROFIBUS-DP

( 2 ) The Gateway ( GW ) Unit can be connected with Manifold Valve / Relay Output Module with the SI Unit, and Input Unit / Input Block can be controlled in a decentralized fashion.

It is not necessary to supply power to I/O unit individually because power supply line is built in the communication port.

( 3 ) Transmission delay time problem will not occur because the communication with each branch is running by separate asynchronized transmission form from upper transmission form.

( 4 ) 16 input points per input manifold and 16 output points per output manifold can be controlled in a decentralized fashion per one branch ( 1CH ) of GW Unit. GW Unit communication ports and in / output can control 128 decentralized I/O points.

！CAUTION

Maximum number of I/O points depends on the communication protocol and the host PLC.

B. Input / Output Unit

( 1 ) Input Unit Manifold ( Input Unit / Input Block )

The Input Block can be increased or decreased by two points. A maximum of 8 blocks can be used on a single input manifold.

( 2 ) Output Manifold Valve / Relay Output Module with the SI Unit ( SV series , VQC series )

The SV series and the VQC series Manifold Valve can be used with the EX500 series SI Unit.

The number of Solenoid Valve and Relay Output Module can be increased / decreased by the block alone. A maximum of 8 Double Solenoid Valve and / or 2 point Relay Output Module can be connected.

And a maximum of 16 Single Solenoid Valve and / or 1 point Relay Output Module can be connected with each channel.

2. System Structure

Host

Remote I/O, DeviceNet, PROFIBUS-DP Power source ( 24V DC )

A

B

Gateway (GW) Unit

5m

A

5m

B

A

	A
B	B
	Tool
- 6 -

Communication line + Power supply line

A : Manifold Valve / Relay Output

Module with the SI Unit

B : Input Unit / Input Block

Image 7

SMC Networks EX500 manual Outline Gateway GW Unit, Input / Output Unit, System Structure

Contents

SMC Corporation ・Safety instructions for electric equipment ・Safety instructions for pneumatic equipment・Level of potential hazard ！ Caution ・Safety instructions for cables ・Safety instructions for power supply Index EX500 Serial System Input / Output Unit Outline Gateway GW UnitSystem Structure Electromagnetic Emission SpecificationTest Procedure Specification Criterion ・EMC Directive 89 / 336 / EEC How to Order 5 0 0 G D N Gateway GW Unit specification DeviceNet communication specification EX500 GDN1 PROFIBUS-DP EN50170 PROFIBUS-DP communication specification EX500 GPR1 2. Input Unit Input Unit specificationInput Unit Manifold 1. Input Manifold How to Order 5 0 0 I E Input Block specification3. Input Block SI Unit for SV series Manifold Valve SI Unit specificationSI Unit Applicable Manifold Valve series Option Electric specificationCommunication Connector Cable for DeviceNet EX500 GDN1 Cable specification How to Order 5 0 0 a C 0 3 0 S S P S 2. Branch Cable with M12 Connector 4. Terminal Plug 3. Power Supply Connector Cable5. Water Proof Cap ・Representative PLC Parts description Display Content Operation settingLED display 2. Operation setting switch SW2 1. Operation setting switch SW1Setting Operation State of SW3 3. Terminating resistance setting switch SW3Layout of scanner I/O Data Rate ・Wiring length How to operate EX500 GDN1 DeviceNet Connection style・Cable specification EDO Figure of setting switch 2. Data rate setting switch SW3 1. Address setting switch SW1I/O memory map ・Communication speed and Longest wiring length How to operate EX500 GPR1 PROFIBUS-DP Communication wiring・Terminating resistance DIA State of SW4 1. Address setting switch SW1, 22. Terminating resistance setting switch SW4 ・In case of corresponding with Word ・In case of corresponding with Double Word Input Unit Power supply must be reset after fixing the short circuitInput Unit Manifold Parts description Correspondence of input number and Input Block Exploded view / Input Unit Manifold ・Parts list Parts name Parts number・Addition of the Input Block SI Unit for SV series Manifold Manifold Valve Parts descriptionSV series VQC series Correspondence of output number and Manifold Valve SI Unit for SV series Manifold How to install the SI UnitSI Unit for VQC series Manifold Single power supply WiringSource wiring Individual power supply DeviceNet EX500 GDN1 communication wiring Communication wiring 1. Communication wiring to PLC2. Communication wiring to the SI Unit and the Input Unit Remote I/O EX500 GAB1 -X1 communication wiring ・In case of M8 Input Block Dimension 10 -1. Gateway GW Unit 10 -2. Input Unit ManifoldStations ・In case of M12 Input Block 10 -3. Manifold Valve ・Whole system Remedies Trouble shooting・Remote I/O communication Remedies Status of NS LED ・DeviceNet communication Remedies・PROFIBUS-DP communication Remedies Status of MS LED