Menu items in the range 100 to 199, relating to the control panels (Continued)

Item number

 

 

Item name

 

 

 

Settings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

109

 

 

 

 

 

 

FORCED EE WHEN

 

 

 

During tape threading and unthreading, and when no cassette is inserted, select

 

 

 

 

 

 

 

TAPE UNTHREAD

 

 

 

whether the setting of the function menu item PB/EE controls the PB/EE setting

 

 

 

 

 

 

 

 

 

 

 

 

for output signals.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF: Control by the function menu item PB/EE

 

 

 

 

 

 

 

 

 

 

 

 

 

[ON]: No control (always E-E signal)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

111

 

 

 

 

 

 

TSO PLAY

 

 

 

Select whether or not to enable tape speed override mode.

 

 

 

 

 

 

 

 

 

 

 

 

[DIS]: Disable tape speed override mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

TSO: Enable tape speed override mode.

 

 

 

116

 

 

 

 

 

 

JOG DIAL RESPONSE

 

Select the tape speed characteristics for the search dial rotation rate (VTR

 

 

 

 

 

 

 

 

 

 

 

 

commands).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[TYPE1]: Tape speed varies linearly over the range –1 to +1.

 

 

 

 

 

 

 

 

 

 

 

 

TYPE2: Tape speed varies stepwise as shown in figurea) below over the range –3

 

 

 

 

 

 

 

 

 

 

 

 

 

to +3. (Characterized by a zone around –1 and +1 where the tape speed is

 

 

 

 

 

 

 

 

 

 

 

 

 

independent of the search dial rotation rate. When playing back an HDCAM

 

 

 

 

 

 

 

 

 

 

 

 

 

tape, however, tape speed characteristic TYPE 4 applies.)

 

 

 

 

 

 

 

 

 

 

 

 

TYPE3: Tape speed varies linearly over the range –3 to +3, as shown in figureb)

 

 

 

 

 

 

 

 

 

 

 

 

 

below.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TYPE4: Tape speed varies stepwise as shown in figurec) below over the range –2

 

 

 

 

 

 

 

 

 

 

 

 

 

to +2. (Characterized by a zone around –1 and +1 where the tape speed is

 

 

 

 

 

 

 

 

 

 

 

 

 

independent of the search dial rotation rate.)

 

 

 

 

 

 

 

 

 

 

 

 

 

117

 

 

 

 

 

 

CONTROL PANEL

 

 

 

Select the control panel function when the PANEL SELECT switch on the switch

 

 

 

 

 

 

 

SELECTION

 

 

 

panel is set to REAR.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[SW]: Only the control panel connected to the CONTROL PANEL connector on

 

 

 

 

 

 

 

 

 

 

 

 

 

the connector panel functions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PARA : The control panels connected to the CONTROL PANEL connectors on

 

 

 

 

 

 

 

 

 

 

 

 

 

the switch panel and connector panel both function.

a)

 

 

 

 

 

b)

 

 

 

 

 

 

 

c)

 

 

 

 

 

(Continued)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Speed

 

 

 

 

 

Speed

 

 

 

Speed

 

 

TYPE 2

 

 

TYPE 3

TYPE 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+3

 

FWD

 

 

 

 

 

+3

 

FWD

+2

 

FWD

 

 

 

 

 

 

 

 

 

 

 

 

 

(reverse)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+1

 

 

 

Rotation rate

 

 

 

 

 

 

 

Rotation rate

+1

 

 

Rotation rate

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RVS

 

 

 

-1

FWD

 

RVS

 

 

 

 

FWD

 

RVS

 

-1

FWD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-3

(forward)

 

 

 

 

 

 

-3

 

 

 

 

 

-2

 

 

 

 

RVS

 

 

 

 

 

RVS

 

 

 

 

RVS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10 Chapter

Menus Setup

Chapter 10 Setup Menus 10-11