Manuals / Sterling / Kitchen Appliance / Blender

Sterling SLC 5/04 Touch “Hopper Setup”, Setting Passwords, User factory set to “5413”, Service

Models: 060 SLC 5/04 015 600 100

1 63

Download 63 pages 38.69 Kb

Page 38

Image 38

Touch “Hopper Setup”

Touch the box next to the hopper number that you want to change and enter weight value.

Setting Passwords

There are three levels of password security for the control system.

-User (factory set to “5413”)

-Service

-ACS only (cannot be changed factory set to “3145348”)

Continuous Loss-in-Weight Blenders

Chapter 3: Installation

Page 38

Image 38

Sterling SLC 5/04, 100, 600, 015 Touch “Hopper Setup”, Setting Passwords, User factory set to “5413”, Service, Installation

Contents

Allen-BradleySLC 5/04 Programmable Controller Continuous Loss-in-WeightBlenders________________________________ PanelView 600 Touch Screen InterfaceIn the Event of Shipping Damage Shipping InformationUnpacking and Inspection If the Shipment is Not CompleteWarranty Returns Credit ReturnsCHAPTER 2: FUNCTIONAL DESCRIPTION Table of ContentsCHAPTER 3: INSTALLATION CHAPTER 4: OPERATIONContinuous Loss-in-WeightBlenders MAINTENANCEAPPENDIX Safety Symbols Used in this Manual Chapter 1: Safety1-1How to Use This Manual Description Continuous Loss-in-WeightBlender Safety TagsDescription 1-2Warnings and Precautions Wear SAFETY GLASSES and WORK GLOVES1-3Responsibility General ResponsibilityOperator Responsibility REMEMBERMaintenance Responsibility Reporting a Safety Defect2-2General Description Chapter 2: Functional Description2-1Models Covered in This Manual AccessoriesController Features 2-3Typical Features & ComponentsMechanical Features Electrical FeaturesIngredient Supply/Re-fillHoppers Figure 2: Continuous Blender AssemblyBlender System Component Description Ingredient Weigh Hoppers Cascade Material Chute Ingredient Metering/Transport Auger AssembliesFigure 3: Metering Auger Components “Fixed Rate” mode Lower Mass Flow Weigh Hopper AssemblyFigure 4: Weigh Hopper Assembly Motor Drive Panel PLC Control PanelTouch Screen Interface Optional “Quick Color Change” Kit•Ethernet communication module 2-4Options•Mezzanine stand with slide gate and 4” tube stub Remote DisplayFail Safe Operation 2-5Safety Devices and InterlocksSafety Circuit Standards Figure 5: Plug Safety Device Lock-OutsPluggable Line Cord 3-2Rigging and Placing the Unit Chapter 3: Installation3-1Uncrating the Equipment Figure 6: Lifting Eyebolt Position on BlenderMachine Mount Mounting ConfigurationSite Requirements Mezzanine Mount Figure 7: Offset Mezzanine Mount PositionFloor Mount 3-3Electrical Installation 3-4Pneumatic Installation Figure 9: Pneumatic Air System3-5Overall Installation Summary Figure 10: Load Cell Mechanical Stop Adjustment 3-6 Set-upLoad Cell Adjustment Final Connections FIFO Diagnostics Controller SetupHopper Setup Alarm logFigure 11: Blender Calibration Weight Scale CalibrationTouch the “Calibration” button Continuous Loss-in-WeightBlendersChapter 3: Installation Feeder Calibration Touch the “OK” button Continuous Loss-in-WeightBlendersChapter 3: Installation Touch the “Calibration” buttonSetting Hopper Size Hopper Diameter Setting hopper sizeFigure 12: Hopper Sizes Approximate HopperService Touch “Hopper Setup”Setting Passwords Continuous Loss-in-WeightBlendersTouch “User Password” To change a password proceed as followsEnter password and touch “OK” Continuous Loss-in-WeightBlendersEnteroriginal password Alarm SetupContinuous Loss-in-WeightBlenders Enter the password and touch “OK”Touch “Alarm Setup” Chapter 3: InstallationCommunications Continuous Loss-in-WeightBlenders Setting Blender for English or MetricEnter the password and touch “OK” Touch “Units” Chapter 3: InstallationChapter 3: Installation How to use FIFO DiagnosticsContinuous Loss-in-WeightBlenders First you must get to the FIFO screenContinuous Loss-in-WeightBlenders Enter the Password and touch “OK”Touch “FIFO Diagnostics” Chapter 3: InstallationContinuous Loss-in-WeightBlenders Chapter 3: InstallationGeneral Operation Chapter 4: Operation4-1 Start-up Manual Backup Control System Figure 14: Typical Controller Display 4-2Controller Description & OperationDisplay Description Chapter 4: Operation Continuous Loss-in-WeightBlendersFigure 15: Blender Menu Structure Standard Unit Continuous Loss-in-WeightBlenders Setting a RecipeClean Out Chapter 4: OperationPhotocopy this page for your maintenance records Chapter 5: Maintenance5-1Preventative Maintenance Schedule System model #Chapter Continuous Loss-in-WeightBlendersMaintenance Spare Parts ChapterAppendix Typical Blender Parts ListAnnex B Information 6-2Addendum Service Supervisor Information Programmable SettingsAdvanced Hopper Options Max WTP/RPM Feed Factor FilterSteady Feed Factor Re-fillPercentageSample Time once in Steady Window for FIFO Advance PID Options mass flow setupPID Timer Steady System LimitExtruder RPM Options PID Integral ConstantFeeder Speed Limits Allowed Extruder RPM Change for Steady Flag Update Time for Prox Method in secondsExtrusion Control Options Feeder Setup No Flow Bits Advanced Alarm OptionsNo Flow Timer Parts Department 6-3Technical AssistanceService Department Sales Department