Manuals / Sterling / Kitchen Appliance / Blender

Sterling 100, 600, 015, SLC 5/04 PID Integral Constant, Feeder Speed Limits, Extruder RPM Options

Models: 060 SLC 5/04 015 600 100

1 63

Download 63 pages 38.69 Kb

Page 60

Image 60

PID Integral Constant

Works the same as the Gain.

Feeder Speed Limits

This allows you to set the minimum and maximum speed for the motor drives as a percentage. The drives are not supposed to be run at less than 8 hertz and should not be run above 115 hertz.

Extruder RPM Options

This gives you the option of having no extruder speed input, writing the extruder speed to the blender through the Ethernet, or using a proximity sensor on the end of the extruder screw.

Continuous Loss-in-Weight Blenders	Chapter 6:	Appendix
	60

Page 60

Image 60

Sterling 100, 600, 015, SLC 5/04, 060 specifications PID Integral Constant, Feeder Speed Limits, Extruder RPM Options

Contents

Continuous Loss-in-WeightBlenders ________________________________Allen-BradleySLC 5/04 Programmable Controller PanelView 600 Touch Screen InterfaceShipping Information Unpacking and InspectionIn the Event of Shipping Damage If the Shipment is Not CompleteWarranty Returns Credit ReturnsTable of Contents CHAPTER 3: INSTALLATIONCHAPTER 2: FUNCTIONAL DESCRIPTION CHAPTER 4: OPERATIONMAINTENANCE APPENDIXContinuous Loss-in-WeightBlenders Chapter 1: Safety 1-1How to Use This ManualSafety Symbols Used in this Manual Continuous Loss-in-WeightBlender Safety Tags DescriptionDescription 1-2Warnings and Precautions Wear SAFETY GLASSES and WORK GLOVES1-3Responsibility General ResponsibilityOperator Responsibility REMEMBERMaintenance Responsibility Reporting a Safety DefectChapter 2: Functional Description 2-1Models Covered in This Manual2-2General Description Accessories2-3Typical Features & Components Mechanical FeaturesController Features Electrical FeaturesFigure 2: Continuous Blender Assembly Blender System Component DescriptionIngredient Supply/Re-fillHoppers Ingredient Weigh Hoppers Ingredient Metering/Transport Auger Assemblies Figure 3: Metering Auger ComponentsCascade Material Chute Lower Mass Flow Weigh Hopper Assembly Figure 4 Weigh Hopper Assembly“Fixed Rate” mode PLC Control Panel Touch Screen InterfaceMotor Drive Panel Optional “Quick Color Change” Kit2-4Options •Mezzanine stand with slide gate and 4” tube stub•Ethernet communication module Remote Display2-5Safety Devices and Interlocks Safety Circuit StandardsFail Safe Operation Safety Device Lock-Outs Pluggable Line CordFigure 5: Plug Chapter 3: Installation 3-1Uncrating the Equipment3-2Rigging and Placing the Unit Figure 6: Lifting Eyebolt Position on BlenderMounting Configuration Site RequirementsMachine Mount Mezzanine Mount Figure 7: Offset Mezzanine Mount PositionFloor Mount 3-3Electrical Installation 3-4Pneumatic Installation Figure 9: Pneumatic Air System3-5Overall Installation Summary 3-6 Set-up Load Cell AdjustmentFigure 10: Load Cell Mechanical Stop Adjustment Final Connections Controller Setup Hopper SetupFIFO Diagnostics Alarm logFigure 11: Blender Calibration Weight Scale CalibrationContinuous Loss-in-WeightBlenders Chapter 3: InstallationTouch the “Calibration” button Feeder Calibration Continuous Loss-in-WeightBlenders Chapter 3: InstallationTouch the “OK” button Touch the “Calibration” buttonSetting Hopper Size Setting hopper size Figure 12 Hopper SizesHopper Diameter Approximate HopperTouch “Hopper Setup” Setting PasswordsService Continuous Loss-in-WeightBlendersTo change a password proceed as follows Enter password and touch “OK”Touch “User Password” Continuous Loss-in-WeightBlendersEnteroriginal password Alarm SetupEnter the password and touch “OK” Touch “Alarm Setup”Continuous Loss-in-WeightBlenders Chapter 3: InstallationCommunications Setting Blender for English or Metric Enter the password and touch “OK” Touch “Units”Continuous Loss-in-WeightBlenders Chapter 3: InstallationHow to use FIFO Diagnostics Continuous Loss-in-WeightBlendersChapter 3: Installation First you must get to the FIFO screenEnter the Password and touch “OK” Touch “FIFO Diagnostics”Continuous Loss-in-WeightBlenders Chapter 3: InstallationContinuous Loss-in-WeightBlenders Chapter 3: InstallationChapter 4: Operation 4-1 Start-upGeneral Operation Manual Backup Control System 4-2Controller Description & Operation Display DescriptionFigure 14: Typical Controller Display Continuous Loss-in-WeightBlenders Figure 15: Blender Menu Structure Standard UnitChapter 4: Operation Setting a Recipe Clean OutContinuous Loss-in-WeightBlenders Chapter 4: OperationChapter 5: Maintenance 5-1Preventative Maintenance SchedulePhotocopy this page for your maintenance records System model #Continuous Loss-in-WeightBlenders MaintenanceChapter Chapter AppendixSpare Parts Typical Blender Parts ListAnnex B Information 6-2Addendum Service Supervisor Information Programmable SettingsAdvanced Hopper Options Feed Factor Filter Steady Feed FactorMax WTP/RPM Re-fillPercentageAdvance PID Options mass flow setup PID TimerSample Time once in Steady Window for FIFO Steady System LimitPID Integral Constant Feeder Speed LimitsExtruder RPM Options Update Time for Prox Method in seconds Extrusion Control Options Feeder SetupAllowed Extruder RPM Change for Steady Flag Advanced Alarm Options No Flow TimerNo Flow Bits 6-3Technical Assistance Service DepartmentParts Department Sales Department