Manuals / Sterling / Kitchen Appliance / Kitchen Utensil

Sterling 1500, 1200, 2000, SMS 850 manual Shut-down, Switch OFF Machine

Models: 1500 SMS 850 2000 1200

1 85

Download 85 pages 10.59 Kb

Page 31

Image 31

4-3 Shut-down

Switch OFF Machine

1.Switch OFF the material in-feed device (accessories).

2.Wait until the remaining grinding material has been shredded, and then switch OFF the shredder (main switch to 0).

3.Switch OFF the material discharge device.

BJ5-615

Chapter 4: Operation

31 of 85

Page 31

Image 31

Sterling 1500, 1200, 2000, SMS 850 manual Shut-down, Switch OFF Machine

Contents

SMS SMS Medium Duty Single Shaft ShredderIf the Shipment is Not Complete Shipping InfoUnpacking and Inspection In the Event of Shipping DamageDisposal Storage, Disposal, TransportationWARNING! Suspended load StorageTable of Contents 1-1How to Use This Manual Chapter 1 SafetySafety Symbols Used in this Manual 1-3Responsibility 1-2General Safety Regulations1-4Warnings and Precautions Possible Remaining RisksType of Danger ActivityPreventative Measures Type of DangerActivity PossiblePreventative Measures Type of DangerActivity PossibleMechanical Section Chapter 2 Functional Description2-1Models Covered in This Manual 2-2General DescriptionMachine Standard Execution 2-3Typical Features and ComponentsMaterial In-feed Additional In-feedDevice In-feedHopperRotor, Cutters, Bed Cutters DriveRotor, cutters, bed cutters EJ5-615 Screen and screen support 17 of Discharge of Shredding MaterialEJ5-615 Chapter 2 Functional DescriptionHydraulic Ram Pulse Push Function Safety Device for Housing Flap 2-4Safety FeaturesProtective Devices V-Beltsand Ram Guards Safety MarkingsPersonal Protective Gear Re-operation Emergency Stop ButtonRequirements at Application Site Chapter 3 InstallationUnloading and Installing the Machine 3-1Uncrating the Equipment3-2Electrical Connections 25 of Chapter 3 InstallationConnection of Emergency Stop Button BJ5-615Machine Check Prior to Start-up General Advice3-3Initial Start-up Checking the Rotational DirectionBJ5-615 Chapter 3 Installation27 of DANGER! Rotating Cutters Chapter 4 Operation4-2Operation Procedures 4-1 Start-upEmptying the Screen standard screen Emptying the Screen hydraulic screen 4-3 Shut-down Switch OFF Machine5-1Preventative Maintenance Schedule Chapter 5 MaintenanceCleaning the Machine 5-2Preventative and Corrective MaintenanceChecking the Protective Devices Mounting the Rotor Replacing the Gear BoxReplacing the Rotor Dismounting the RotorDismounting the Main Bearings Replacing the Main BearingsMounting the Main Bearings Replace Lubricant Lubricating the Main BearingsLubrication Intervals Shift OperationRefilling lubricant Replacing or Refilling LubricantReplacing Lubricant Roller Bearing Grease Chapter 5 MaintenanceList of Recommended Lubricants Country of Manufacturer/ManufacturerBJ5-615 Chapter 5 Maintenance39 of V-Belts Tightening Torque of the ScrewsReplacing the Screen Standard Screen and Hydraulic ScreenEfficiency of x in Checking the tension force of the V-beltroller centres and 16mm sag Profile sectionWorking on the Cutting Cutters Checking V-beltcondition, replacing V-beltGrade TorqueGrade Screw typeNOTE See previous drawing Dismounting the Cutter HoldersDismounting the Bed Cutters 2.Insert cutter holder into the pocket 1.Clean the cutter pocket and the cutter holderChapter 5 Maintenance Mounting the Cutter Holders5.Make sure the cutter fits planar in the seat Mounting the CuttersMounting the Bed Cutters Sharpening Cutters and Bed Knives Setting the Cutting Knives Danger of cutting caused by sharp cutting cutters BJ5-615 52 of Chapter 5 MaintenanceHydraulic liquid recommendation BJ5-6156-1Introduction Chapter 6 TroubleshootingPossible Cause Problemconsulting the service service departmentPossible Cause Problemservice department consulting the servicePossible Remedy Problemconsulting the service Possible CauseCredit Returns AppendixWarranty Returns A-1Returned Material Policy58 of A-2Technical SpecificationsBJ5-615 0AppendixCutter Mounting A-3Drawings and Diagrams60 of Bed Knife MountingBJ5-615 0Appendix61 of Rotor AssemblyBJ5-615 0Appendix62 of DriveBJ5-615 0Appendix0Appendix BJ5-61563 of 64 of Ram scraperBJ5-615 0Appendix65 of SMS 850 Hydraulic DiagramBJ5-615 0Appendix66 of SMS 850 Hydraulic UnitBJ5-615 0Appendix67 of SMS 850 Hydraulic Screen DiagramBJ5-615 0Appendix68 of SMS 850 Hydraulic Unit-ScreenBJ5-615 0Appendix69 of SMS 1200-2000Standard Hydraulic DiagramBJ5-615 0Appendix70 of SMS 1200-2000Hydraulic UnitBJ5-615 0Appendix71 of SMS 1200-2000Hydraulic Screen DiagramBJ5-615 0Appendix72 of SMS 1200-2000Hydraulic UnitBJ5-615 0AppendixScreen complete Standard A-4Spare Parts ListDescription/Standard Machine completeE-kniferotor ø387x850 BJ5-6150Appendix 74 ofScreen complete Standard HydraulicElectrical parts Description/StandardBearing BJ5-6150Appendix 76 ofDescription/Standard Ram completeHydraulic Electrical partsScreen complete Standard BJ5-6150Appendix 78 ofE-kniferotor ø457x1410 BJ5-6150Appendix 79 ofScreen complete Hydraulic Electrical partsDescription/Standard Machine completeE-kniferotor ø457x1950 BJ5-6150Appendix 81 ofDescription SMS 850 Hydraulic Unit Spare PartsHydraulic Electrical partsDescription SMS 850 Hydraulic Screen Spare PartsSMS 1200-2000Hydraulic Unit Spare Parts SMS 1200-2000Hydraulic Screen Spare PartsSales Department Service DepartmentA-5Technical Assistance Parts Department85 of Sterling, Inc 2900 S. 160th Street New Berlin, WIBJ5-615 0Appendix