CARE AND CLEANING
•ALWAYS turn your slow cooker off, unplug it from the electrical outlet, and allow it to cool before cleaning.
•The lid and stoneware can be washed in the dishwasher or with hot, soapy water. Do not use abrasive cleaning compounds or scouring pads. A cloth, sponge, or rubber spatula will usually remove the residue. To remove water spots and other stains, use a
•As with any fine ceramic, the stoneware will not withstand sudden temperature changes. Do not wash the stoneware with cold water when it is hot.
•The outside of the heating base may be cleaned with a soft cloth and WARM, soapy water. Wipe dry. Do not use abrasive cleaners.
•The temperature probe can be washed in WARM, soapy water and wiped dry.
•The temperature probe housing is removable for cleaning. Simply slide housing up to remove.
•The housing is dishwasher safe (top rack only), or can be washed in WARM, soapy water and wiped dry.
CAUTION: Never immerse the heating base in water or other liquid.
•No other servicing should be performed.
TROUBLESHOOTING
Situation | Solution | ||
Slow cooker not | • | Make sure appliance is properly plugged into a wall outlet and the | |
| outlet is energized (check fuses or circuit breaker). | ||
operating |
| ||
• | If a power outage has occurred, | ||
| |||
Display is blinking | • | Display will blink until you program your cooking mode. | |
Display reads “PROB | • | Probe cord is not fully inserted into probe jack. | |
OUT” | |||
• | If you remove the probe cord from the probe jack while the slow | ||
Note: the |
| cooker is on, PROB OUT will display until you plug it back into the | |
| temperature probe jack. | ||
temperature probe is |
| ||
• | After making sure probe cord is fully inserted into the probe jack, | ||
only for use with Auto | |||
Cook Mode |
| press Start/Stop and reset the Auto Cook Mode. | |
|
| ||
When selecting |
|
| |
temperature (LOW | • | Press TEMP button again to select either LOW or HIGH | |
or HIGH), CYCLE light | |||
illuminates |
|
| |
Changing settings or | • | To change any settings or cooking modes after you have already | |
| pressed START/STOP, make your new selections and press START/ | ||
cooking modes during | • | STOP again to activate the new settings. | |
programming | If using Auto Cook Mode, you must remove the probe cord from | ||
|
| the probe jack before selecting another cooking mode. | |
Display clears when | • | If more than 10 seconds elapse between button presses, display | |
trying to program the | |||
slow cooker |
| clears (goes blank) and you must start again. | |
|
| ||
In Auto Cook Mode, | • | Make sure temperature probe cord is fully inserted into | |
display immediately | |||
reads a HIGH | • | temperature probe jack. | |
temperature and | If you remove probe cord from probe jack during programming or | ||
suddenly switches to |
| cooking, you must reset the Auto Cook Mode. | |
SIMR |
|
| |
Slight smoke or odor | • | This is normal with many new heating appliances and will | |
during initial use |
| subside after the first few uses. | |
Food under- or | • | See COOKING TIPS. | |
• | If using Auto Cook Mode, make sure probe cord is fully inserted | ||
overcooked |
| into probe jack, and probe TIP is fully inserted into the center of | |
|
| the meat or dish. | |
Slow cooker exterior | • | This is normal with many heating appliances. | |
• | Always use oven mitts or hot pads when handling, and place a hot | ||
is hot | |||
| pad under your slow cooker. | ||
|
| ||
Slow cooker runs | • | Timer will automatically switch to WARM or SIMR after set time | |
indefinitely |
| elapses and until you manually shut it off. |
13 | 14 |
6 QT | 4/17/08 6:21:20 PM |