Problem Solution | Sunwave Tech SRC-3310/9320 manual

SRC-93 SERIES User’s Manual

	Problem	Solution
	You cannot	Make sure that you have correctly
	operate a device	“taught” your device’s remote control to
	even after	the SRC-93 SERIES. (page 21)
	teaching the	Delete the device data from the SRC-93
	device using the	Delete the device data from the SRC-93
	device using the	SERIES and carry out the learning
	learning function.	SERIES and carry out the learning
	learning function.	function again. (page 25)
		function again. (page 25)
		Make sure you did not program more
		than one remote for a given device.
	You see “ERROR”	Make sure you hold the other remote’s
	display on the LCD	button down for about 2 seconds.
	during the learning	Make sure you did not program more
	procedure.	Make sure you did not program more
	procedure.	than one remote for a given device.
		than one remote for a given device.
		Make sure the two remotes are not too
		close or too far apart and are aiming
		directly at each other - keep apart
		between 2~4 inches (5~10cm ).
	You see “ERROR”	The button that you pressed has not
	display during	been taught. Teach the button using the
	operation.	learning procedure. (page 20)
	Your VCR will not	As a safety feature on SRC-93 SERIES,
	record.	you must press the REC key for 2
		seconds.
	Problems changing	If your original remote requires the ENTER
	channels.	key to be pressed after a channel is
		selected, press the ENTER key to select
		the channel.
	Macro does not	Be sure to aim the SRC-93 SERIES at the
	work.	devices while the macro commands are
		being sent.
		Macro was not properly set up. Repeat
		macro set-up procedure. (page 29)

46

Image 50

Sunwave Tech SRC-3310/9320 manual Problem Solution

Contents

SRC-9310/9320 031021 Preface Table of Contents Controlling Devices Alkaline Battery Introducing the SRC-93 Series Unpacking the SRC-93 Series SRC-93 Series FeaturesFollowing list identifies the SRC-93’s key features Identifying Components Front and Rear Views Features Overview Getting StartedPage Installing Batteries Installing Batteries Battery Low Indicator Battery Tips and Precautions Turning the Touch Screen On Touch Screen PrecautionsTouch Screen Please read the following instructions carefully Rubber Buttons Touch Screen Buttons Menus Confirm Menu Entry by Pressing Numbers Setup Menu Menu Description Delete Menu Macro Menu Choosing a Device Setting Up the SRC-93 Series to Control a DevicePress and hold the Setup button on Touch Screen Creating a New Device Press the OK button to confirm Re-Labeling DevicesModifying an Existing Device Changing Touch Screen Layout Press OK to confirm your changes Programming Infrared CodesTouch the button that you wish to change Using Manufacturer Codes There are two ways to program the manufacture codes To use manual entry Power button or Auto button to stop the automatic search To use automatic search Using the Learning Function Before Using the Learning Function Learning from Another Remote Control Press and hold the Setup button on the Touch Screen Rubber Keys SoftKey To collect unrecognized codes Collecting Unrecognized Infrared CodesAll unrecognized codes should be sent to this address Press and hold the Delete button on the Touch Screen Deleting a Specific KeyDeleting a Device Select the key you want to erase To delete a device from the SRC-93 Series follow these steps Select the device you wish to delete Changing Touch Screen Controlling DevicesSelecting Device to Control Using the AUX Key Controlling the Device Creating a Macro Sequence Creating and Using MacrosIntroduction to Macros Set up the macro using the following steps Press OK to save the Macro Using Macros Deleting a Macro SRC-93 Series has the following additional features Other FeaturesUsing Timers Setting Up a New Timer Press and hold the Macro button on the Touch Screen Use the arrow keys to select the time Using Quick Channel ListsWhen finished press the Exit key to leave the Macro Menu Setting up Quick Channel Lists Press and hold the Delete button on Touch Screen Press Exit when finished and leave the Delete menuDeleting Channels from a Quick Channel List Transmitting System Setup Using Quick Channel Lists Using Sleep Mode To use sleep mode Date and Clock Press OK when finished Now set the hour, and minutesDisplaying Version Number Enter the year, month, and date first Backlight On Time Period Power Down Time PeriodUse the arrow keys to set the power down time Use the arrow keys to set the backlight period Beep Toggling Resetting to Factory DefaultsPress OK to reset the SRC-93 Use the OK button to toggle the beep from on to OFF Appendix a Specifications Model SRC-9310 SRC-9320 USB cable Appendix B AccessoriesSLC-2080 Appendix C Troubleshooting Problem Solution Problem Solution IR Learning