Connecting the Control Panel | SUPER MICRO Computer 6012P-6 specification

SUPERSERVER 6012P-6 User’s Manual

Connecting the Control Panel

JF2 contains header pins for various front control panel connectors. See Figure 5-3 for the pin locations of the various front control panel buttons and LED indicators. Please note that even and odd numbered pins are on opposite sides of each header.

All JF2 wires have been bundled into single ribbon cable to simplify their connection. Make sure the red wire plugs into pin 1 as marked on the board. The other end connects to the Control Panel printed circuit board, located just behind the system status LEDs in the chassis.

See the Connector Definitions section in this chapter for details and pin descriptions of JF2.

Figure 5-3. P4DPR-6GM+ Front Control Panel Header Pins

NMI X Power LED

HDD LED

NIC1 LED NIC2 LED

Overheat LED Power Fail Button

Ground

Ground

20	19
	Ground
	X
	Vcc

Vcc

Vcc

Vcc

Vcc

Vcc

Reset Reset Button

Pwr Power Button

2 1

5-6

Image 42

SUPER MICRO Computer 6012P-6 user manual Connecting the Control Panel, P4DPR-6GM+ Front Control Panel Header Pins

Contents

Super Page Preface About This ManualManual Organization Advanced Chassis Setup System SafetyAdvanced Motherboard Setup Bios Preface Table of Contents System Safety Advanced Motherboard Setup Advanced Chassis Setup Bios AppendicesPage Chapter Introduction to the SuperServer 6012P-6 Overview Mainboard Features Chipset PCI Expansion Slots Processors MemoryOnboard Scsi ATI Graphics Controller Other Features Onboard Controllers/Ports Scsi Subsystem Server Chassis FeaturesSystem Power Control Panel Cooling System I/O Backplane European Office Contacting SupermicroHeadquarters Asia-Pacific Superserver 6012P-6 Manual Chapter Server Installation Preparing for SetupUnpacking the SuperServer 6012P-6 Choosing a Setup Location Rack PrecautionsServer Precautions Installing the SuperServer 6012P-6 into a Rack Identifying the Sections of the Rack Rails Installing the Chassis Rails Installing the Rack Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Motherboard Setup Superserver 6012P-6 Manual Checking the Drive Bay Setup Superserver 6012P-6 Manual Chapter System Interface Control Panel Buttons Control Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Handling the P4DPR-6GM+ Motherboard Chapter Advanced Motherboard SetupPrecautions Unpacking PGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel P4DPR-6GM+ Front Control Panel Header Pins Installing Memory Dimm Installation See FigureI/O Ports Side View of Dimm Installation into Slot Memory Support PCI card installation Adding PCI CardsPCI slots Motherboard Layout P4DPR-6GM+ Jumper Description Default Setting Connector DescriptionP4DPR-6GM+ Quick Reference Power LED Connector DefinitionsATX Power Connection Pwrsec Connection Power Fail LED Reset ButtonOverheat LED OH Power Button Universal Serial Bus USB0/1Extra Universal Serial Bus Headers FPUSB0/1 Fan Headers Serial PortsATX PS/2 Keyboard and PS/2 Mouse Ports LAN1/2 Ethernet Ports Wake-On-LAN Wake-On-RingKeylock Jumper Settings Explanation JumpersCmos Clear VGA Enable/Disable LAN1 Enable/DisableLAN2 Enable/Disable Chassis/Overheat Fan Select Scsi Enable/Disable Scsi Termination Enable/ DisableWatchdog Enable/Disable PCI-X Bus Speed Settings Onboard IndicatorsThermal Fan Enable/Disable Speaker Enable/Disable Floppy Connector Floppy/Hard Disk Drive and Scsi Connections IDE Connectors Ultra160 Scsi Connectors Installing Software Drivers Driver/Tool Installation Display Screen Superserver 6012P-6 User’s Manual Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Control Panel Chassis Front and Rear Views System Fan Failure Installing a new fanSystem Fans Replacing System Cooling Fans Drive Bay Installation/Removal Accessing the Drive Bays Scsi Drive Installation Mounting a Scsi drive in a drive carrier Installing/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA Backplane Removing/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supply Removing/Replacing the Power Supply Superserver 6012P-6 Manual Starting the Setup Utility System BiosHow To Change the Configuration Data Chapter Running Setup Main Bios SetupPress the Delete key to enter Setup System Time Main Bios Setup MenuMain Setup Features System Date Legacy Diskette a Legacy Diskette B Ultra DMA Mode LBA Mode ControlTransfer Mode Type Advanced Setup Installed OSQuick Boot Mode Device Configuration Quiet BootReset Configuration Data Power Loss Control Mode InterruptSerial Port B Parallel Port DMA Channel Large Disk Access ModeEnable Memory Gap Floppy Disk Controller Serr Signal Condition ECC ConfigurationECC Error Type Advanced Processor Options L3 Cache Split Lock OperationsHyper-threading DMI Event Logging COM Port Address Clear All DMI Event LogsConsole Redirection Baud Rate Supervisor Password Is User Password IsSecurity Password on Boot Set Supervisor PasswordSet User Password Fixed Disk Boot Sector Power Acpi ModePower Savings Resume on Time Standby TimeoutAuto Suspend Timeout Resume Time Boot +Removable DevicesCD-ROM Drive Network Boot +Hard DriveIntel UNDI, PXE-2.0 PIR Select the Processors PIRSelect the Thermal Unit Processor Info ROM Data Exit Exit Exit Discarding Changes Load Setup DefaultsExit Saving Changes Discard Changes Appendix a PhoenixBIOS Post Messages Real time clock error System Cmos checksum bad Default configuration usedSystem timer error Check date and time settings Allocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering Setup Fixed Disk n Invalid System Configuration DataPS/2 Mouse Boot Summary Screen Device IRQ conflict Run the I2O Configuration Utility Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup System Bios shadowed Superserver 6012P-6 Manual Terminal Post Errors Appendix B PhoenixBIOS Post CodesRecoverable Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Superserver 6012P-6 Manual Key Features Appendix C Supero Doctor Linux Support Figure C-1. Supero Doctor III Health Information Screen Appendix C Supero Doctor Superserver 6012P-6 Manual Appendix D System Specifications Weight Power SupplyDimensions Expansion Slots provided with butterfly riser card