Wake-On-LAN, Wake-On-Ring, Keylock | SUPER MICRO Computer 6012P-6

SUPERSERVER 6012P-6 User’s Manual

Wake-On-LAN

The Wake-On-LAN header is des- ignated as WOL. See the table on the right for pin definitions. You must enable the LAN Wake-Up set- ting in BIOS to use this feature. You must also have a LAN card with a Wake-on-LAN connector and cable.

Wake-On-LAN Pin Definitions (WOL)

Pin
Number	Definition

1+5V Standby

2Ground

3W ake-up

Wake-On-Ring

The Wake-On-Ring header is des- ignated WOR. This function al- lows your computer to receive and "wake-up" by an incoming call to the modem when in sustpend state. See the table on the right for pin definitions. You must have a WOR card and cable to use this feature.

Keylock

The keyboard lock connection is lo- cated on JP35. Utilizing this header allows you to inhibit any actions made on the keyboard, effectively "locking" it.

Wake-on-Ring

Pin Definitions

(WOR)

Pin

Number Definition

1Ground

2W ake-up

5-16

Image 52

SUPER MICRO Computer 6012P-6 user manual Wake-On-LAN, Wake-On-Ring, Keylock

Contents

Super Page About This Manual PrefaceManual Organization System Safety Advanced Motherboard SetupAdvanced Chassis Setup Bios Preface Table of Contents System Safety Advanced Motherboard Setup Advanced Chassis Setup Bios AppendicesPage Chapter Introduction to the SuperServer 6012P-6 Overview Mainboard Features Chipset Processors Memory Onboard ScsiPCI Expansion Slots ATI Graphics Controller Other Features Onboard Controllers/Ports Server Chassis Features System PowerScsi Subsystem Control Panel Cooling System I/O Backplane Contacting Supermicro HeadquartersEuropean Office Asia-Pacific Superserver 6012P-6 Manual Preparing for Setup Chapter Server InstallationUnpacking the SuperServer 6012P-6 Rack Precautions Choosing a Setup LocationServer Precautions Installing the SuperServer 6012P-6 into a Rack Identifying the Sections of the Rack Rails Installing the Chassis Rails Installing the Rack Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Motherboard Setup Superserver 6012P-6 Manual Checking the Drive Bay Setup Superserver 6012P-6 Manual Chapter System Interface Control Panel Buttons Control Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Motherboard Setup PrecautionsHandling the P4DPR-6GM+ Motherboard Unpacking PGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel P4DPR-6GM+ Front Control Panel Header Pins Dimm Installation See Figure Installing MemoryI/O Ports Side View of Dimm Installation into Slot Memory Support Adding PCI Cards PCI card installationPCI slots Motherboard Layout P4DPR-6GM+ Connector Description Jumper Description Default SettingP4DPR-6GM+ Quick Reference Connector Definitions ATX Power ConnectionPower LED Pwrsec Connection Reset Button Power Fail LEDOverheat LED OH Universal Serial Bus USB0/1 Power ButtonExtra Universal Serial Bus Headers FPUSB0/1 Serial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsFan Headers LAN1/2 Ethernet Ports Wake-On-Ring Wake-On-LANKeylock Explanation Jumpers Jumper SettingsCmos Clear LAN1 Enable/Disable LAN2 Enable/DisableVGA Enable/Disable Chassis/Overheat Fan Select Scsi Termination Enable/ Disable Scsi Enable/DisableWatchdog Enable/Disable Onboard Indicators Thermal Fan Enable/DisablePCI-X Bus Speed Settings Speaker Enable/Disable Floppy Connector Floppy/Hard Disk Drive and Scsi Connections IDE Connectors Ultra160 Scsi Connectors Installing Software Drivers Driver/Tool Installation Display Screen Superserver 6012P-6 User’s Manual Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear Views Installing a new fan System FansSystem Fan Failure Replacing System Cooling Fans Drive Bay Installation/Removal Accessing the Drive Bays Scsi Drive Installation Mounting a Scsi drive in a drive carrier Installing/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA Backplane Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supply Removing/Replacing the Power Supply Superserver 6012P-6 Manual System Bios How To Change the Configuration DataStarting the Setup Utility Chapter Main Bios Setup Running SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup FeaturesSystem Time System Date Legacy Diskette a Legacy Diskette B LBA Mode Control Transfer ModeUltra DMA Mode Type Installed OS Advanced SetupQuick Boot Mode Quiet Boot Reset Configuration DataDevice Configuration Power Loss Control Interrupt Serial Port BMode Parallel Port Large Disk Access Mode Enable Memory GapDMA Channel Floppy Disk Controller ECC Configuration ECC Error TypeSerr Signal Condition Advanced Processor Options Split Lock Operations Hyper-threadingL3 Cache DMI Event Logging Clear All DMI Event Logs Console RedirectionCOM Port Address Baud Rate User Password Is Supervisor Password IsSecurity Set Supervisor Password Set User PasswordPassword on Boot Fixed Disk Boot Sector Acpi Mode PowerPower Savings Standby Timeout Auto Suspend TimeoutResume on Time Resume Time +Removable Devices BootCD-ROM Drive +Hard Drive Network BootIntel UNDI, PXE-2.0 Select the Processors PIR PIRSelect the Thermal Unit Processor Info ROM Data Exit Exit Load Setup Defaults Exit Saving ChangesExit Discarding Changes Discard Changes Appendix a PhoenixBIOS Post Messages System Cmos checksum bad Default configuration used System timer errorReal time clock error Check date and time settings System cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering Setup Invalid System Configuration Data PS/2 Mouse Boot Summary ScreenFixed Disk n Device IRQ conflict Press F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupRun the I2O Configuration Utility System Bios shadowed Superserver 6012P-6 Manual Appendix B PhoenixBIOS Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Superserver 6012P-6 Manual Key Features Appendix C Supero Doctor Linux Support Figure C-1. Supero Doctor III Health Information Screen Appendix C Supero Doctor Superserver 6012P-6 Manual Appendix D System Specifications Power Supply DimensionsWeight Expansion Slots provided with butterfly riser card