Manuals / TANDBERG / Computer Equipment / Network Router

TANDBERG D13202 manual Introduction

Models: D13202

1 32

Download 32 pages 14.21 Kb

Page 3

TANDBERG GW

Dataport Command Interface User Guide

1.Introduction

The TANDBERG GW Dataport Command Interface User Guide contains guidelines on how to use the textual command interface supported by the GW. The Dataport Command Interface can be accessed through Telnet via the LAN interface or through RS-232 by connecting a serial cable to the serial interface connector, referred to as the Dataport (ref. chapter 2). Three Telnet sessions can be connected to the GW at the same time in addition to the RS-232 connection.

If, after reading this manual, you require additional information concerning the use of the TANDBERG GW Dataport Command Interface, please contact your local TANDBERG dealer who will be able to supply you with relevant information for special applications.

D13202 Rev 01

3

Image 3

TANDBERG D13202 manual Introduction

Contents

part without the permission in writing from TANDBERG Software version G1.0TANDBERG GW Dataport Command Interface User Guide This document is not to be reproduced in whole or in4. THE TANDBERG GW COMMANDS Table of Contents2. CONNECTING TO THE DATAPORT COMMAND INTERFACE THROUGH THE RS 3. CONNECTING TO THE DATPORT COMMAND INTERFACE USING TELNET1. Introduction DTE, 9 pin 2.1. Hardware And CablingTANDBERG GW DCE, 9 pin2.3. Troubleshooting 2.2. Configuring The Dataport From The Web InterfaceWelcome to TANDBERG TANDBERG GW Release G1.0 SW Release Date 3. Connecting to the Datport Command Interface using Telnet4.1. Introduction 4. The TANDBERG GW Commands4.1.1. Command format 4.1.2. Command typespardial 4.2. The commandscalltransfer 1 pardial on4.2.1. System Configuration Commands ipassignment LAN interface dhcp/static ippasswordippassword LAN interface password ipassignmentipqos isdnprot sendcomplete on/off isdnprotisdnprot nsftel number isdnprot nsfvid numberpricable network auto/h320/h323pardial pardial on/offP prichan a max prichan PRI interface low 1..23/31prichan PRI interface high 1..23/31 prichan PRI interface search high/lowprinumbrange snmp cn community name sendnumsendnum on/off snmpParameters name Textstring of maximum 16 characters TANDBERG GWDataport Command Interface User Guidesystemname systemname nameNOTE! The user should be aware not to overwrite existing entries 4.2.2. General GW Commandscommand NOTE! This parameter will be overridden when using calltransferdisc gwid Page customformats Sets custom format support to on or off gwsettings duovideo on/off or gwsettings encryption on/offsub-commands natvid Sets natural video support to on or off Dataport Command Interface User GuideS callstatus 1 outgoing bonding connected 255 2446Sec 4.2.3. System Status CommandsS chanstat a 28 connect 123456789 255255 334Sec S encstatus 11 des des 9FE389C8F664F3F5D13202 Rev S gwcalls 1 1 22222222 2 sentreceived loss jitterms ipcallstatisticsipcallstatistics ipcallstatistics callid protocol chantype direction rateS statin 1 outgoing synced norestrict h323-1920 g722 h263 cif unknown S pristatus b active 30 24S statout 1 outgoing synced norestrict h323-768 g722 h263 cif unknown 4.2.4. Debug Commands 6 146.172.254.249 40 ms 7 146.172.248.5 40 ms 8 146.172.248.9 40 ms P feedback off 4.2.5. Special CommandsCommand 4.3. Parameter Storage4.4. Index Commands