Manuals / Texas Instruments / Computer Equipment / Network Router

Texas Instruments manual Appendix A Revision History, TMS320C6457 HPI Revision History

Models: TMS320C6457

1 43

Download 43 pages 41.83 Kb

Page 42

Appendix A Revision History

www.ti.com

Appendix A Revision History

This revision history highlights the technical changes made to the document in this revision.

Table 11. TMS320C6457 HPI Revision History

SeeAdditions/Modifications/Deletions

Table 6

Modified table

42

Revision History

SPRUGK7A –March 2009 –Revised July 2010

Copyright © 2009–2010, Texas Instruments Incorporated

Image 42

Texas Instruments manual Appendix A Revision History, TMS320C6457 HPI Revision History, Modified table

Contents

Users Guide TMS320C6457 DSP Host Port Interface HPISPRUGK7A -March 2009 -Revised July Copyright 2009-2010, Texas Instruments IncorporatedIntroduction to the HPI List of Figures List of FiguresList of Tables About This Manual Read This FirstPreface Notational Conventions1 Introduction to the HPI Host Port Interface HPIUsers Guide Figure 1. HPI Position in the Host-DSP System1.1 Summary of the HPI Registers Introduction to the HPI1.2 Summary of the HPI Signals Table 2. HPI SignalsTable 1. Summary of HPI Registers Introduction to the HPI Table 2. HPI Signalscontinued Host Port Interface HPI2 Using the Address Registers 2.1 Single-HPIA Mode2.2 Dual-HPIA Mode 3.1 Host-HPI Signal Connections in the 32-Bit Multiplexed Mode3 HPI Operation in the 32-Bit Multiplexed Mode in the 16-Bit Multiplexed Mode3.2 HPI Configuration and Data Flow Multiplexed ModeTable 3. Options for Connecting Host and HPI Data Strobe Pins 3.3 HDS2, HDS1, and HCS Data Strobing and Chip SelectionFigure 6. HPI Strobe and Select Logic Table 4. Access Types Selectable by the HCNTL Signals Table 5. Cycle Types Selectable With the HCNTL and HR/W Signals3.4 HCNTL10 and HR/W Indicating the Cycle Type 3.6 HAS Forcing the HPI to Latch Control Information Early Figure 7. 16-Bit Multiplexed Mode Host Read Cycle Using HAS HPI OperationHost Port Interface HPI Figure 8. 16-Bit Multiplexed Mode Host Write Cycle Using HAS HPI OperationHost Port Interface HPI 3.7 Performing a Multiplexed Access Without HAS Figure 9. 16-Bit Multiplexed Mode Host Read Cycle With HAS Tied HighHPI Operation Host Port Interface HPI3.8 Single-Halfword HPIC Cycle in the 16-Bit Multiplexed Mode 3.9 Hardware Handshaking Using the HPI-Ready HRDY Signal3.9.1 HRDY Behavior During 16-Bit Multiplexed Read Operations Case 1 HPIA Write Cycle Followed by Nonautoincrement HPID Read CycleCase 2 HPIA Write Cycle Followed by Autoincrement HPID Read Cycles 3.9.2 HRDY Behavior During 16-Bit Multiplexed Write Operations Case 1 No AutoincrementingCase 2 Autoincrementing Selected, FIFO Empty Before Write Case 3 Autoincrementing Selected, FIFO Not Empty Before Write 3.9.3 HRDY Behavior During 32-Bit Multiplexed Read OperationsCase 2 HPIA Write Cycle Followed by Autoincrement HPID Read Cycles Figure 21 shows an HPIA HCNTL10 = 10b write access followed by several autoincrement HPID HCNTL10 = 01b read accesses. Note that HRDY is active for the HPIA access. HRDY is also active for the first HPID read access, but not for subsequent read accessesCase 1 HPIA Write Cycle Followed by Nonautoincrement HPID Read Cycle 3.9.4 HRDY Behavior During 32-Bit Multiplexed Write OperationsFigure 23 shows an HPIA HCNTL10 = 10b write access followed by an HPID HCNTL10 = 11b write access for 32-bit multiplexed HPI operation Case 1 No AutoincrementingFigure 25 shows an HPIA HCNTL10 = 10b write access when the write FIFO is not empty, followed by several autoincrementing HPID HCNTL10 = 01b write accesses. Note that HRDY is active twice for the HPIA access. This occurs because the FIFO is not empty and the data in the FIFO must first be written to memory. This results in an HRDY assertion immediately after the falling edge of the datastrobe HSTRB. When a write request to memory has been made that will empty the internal FIFO, the HPIA write operation can complete with the rising edge of HSTRB. The second HRDY assertion is for the write to the HPIA register. HRDY is not active for the HPID accesses Case 2 Autoincrementing Selected, FIFO Empty Before WriteCase 3 Autoincrementing Selected, FIFO Not Empty Before Write 4 Software Handshaking Using the HPI Ready HRDY Bit 4.1 Polling the HRDY Bit5.1 DSPINT Bit Host-to-CPU Interrupts Figure 26. Host-to-CPU Interrupt State Diagram5 Interrupts Between the Host and the CPU 5.2 HINT Bit CPU-to-Host InterruptsInterrupt active HINT bit=1 HINT signal is low Figure 27. CPU-to-Host Interrupt State DiagramNo interrupt interrupt cleared HINT bit=0 HINT signal is high CPU writes 0 to HINT bit6 FIFOs and Bursting 6.1 Read BurstingFigure 28. FIFOs in the HPI 6.2 Write Bursting 6.4 FIFO Behavior When a Hardware Reset or Software Reset Occurs 6.3 FIFO Flush Conditions7.3 Hardware Reset Considerations 7 Emulation and Reset Considerations7.2 Software Reset Considerations 7.1 Emulation ModesTable 6. Host Port Interface HPI Registers 8 HPI Registers8.1 Introduction HPI RegistersHPI Registers 8.2 Power and Emulation Management Register PWREMUMGMTFigure 29. Power and Emulation Management Register PWREMUMGMT Host Port Interface HPI8.3 Host Port Interface Control Register HPIC Figure 30. Host Access PermissionsFigure 31. CPU Access Permissions Table 8. Host Port Interface Control Register HPIC Field DescriptionsDescription FieldValue For host write cycle8.4 Host Port Interface Address Registers HPIAW and HPIAR LEGEND R = Read only W = Write -n = value after reset31-0 ADDRESS R-0 LEGEND R = Read only -n = value after reset 31-0 ADDRESS R/W-08.5 Data Register HPID Table 10. Data Register HPID Field DescriptionsModified table Appendix A Revision HistoryTable 11. TMS320C6457 HPI Revision History Revision Historyamplifier.ti.com power.ti.comIMPORTANT NOTICE dataconverter.ti.com