Toshiba 42HP95 Programming the remote control to operate your other devices, Device code setup

Chapter 3: Using the remote control

Programming the remote control to operate your other devices

Device code setup		Searching and sampling the code of
	1. Refer to the multi-brand remote control device code table	a device (8500)
	on pages 35 and 36 to find the code for the brand of your	If you do not know the device code for a particular device, you
	device.
		can cycle the remote control through the available codes for that
	If more than one code is listed, try each one separately until
		device mode and sample the functions to find the code that
	you find one that works.
		operates the target device. The keys available to be sampled,
	2. Press MODE until the Mode indicator for the device
		provided they are applicable to that mode, are POWER, 1,
	(CBL/SAT, VCR/PVR, DVD, AUDIO 1, AUDIO 2) lights	VOL y, CH y, and PLAY. Invalid keys will be ignored while in
	up.	program mode.
	3. While holding down the RECALL button, press the	To cycle through each available device code and sample its
	Channel Number buttons to enter the four-digit code for
		functions:
	your brand of device. If a valid code is entered, the mode
		1. Press MODE to select the mode you want to set up.
	indicator will blink twice. If an invalid code is entered, the
		2. While holding down RECALL, press 8 – 5 – 0 – 0. The
	mode indicator will blink one long blink.
	4. Point the remote control at the device and press POWER to	remote control will enter program mode.
		3. Point the remote control at the target device and press
	test the code.
	If the device responds to the remote control:	POWER (or other function buttons that are available to be
		sampled).
	You have entered the correct code.
		4. If the device responds to the remote control:
	If the device does not respond to the remote control:
		Press RECALL to store the device code. The mode
	You may have entered the wrong code. Repeat steps 3
	and 4 using another code.	indicator will blink twice and the remote control will exit
	Note: In addition to POWER, confirm that all necessary keys	the program mode.
		If the device does not respond to the remote control:
	on the TV remote control operate your device. If some keys
	are not operational, repeat the device code setup using	Press y, and then press POWER. Repeat this step until
	another code (if other codes are listed for your device). If,	the device responds to the remote control, and then press
	after trying all listed codes, the necessary keys do not operate
		RECALL.
	your device, use the deviceÕs original remote control.
		Note: When a search cycle is completed, the mode
	5. To control the TV, repeatedly press MODE to select “TV.”
		indicator will blink three times. The remote control will
Note:		begin to cycle through the available codes again. If no
		key is pressed within 10 seconds while programming, the
¥	Although the TV remote control includes codes for many devices, it may
		remote control will exit the program mode and return to
	not include codes for some or all of the features on certain devices you
		the previous code.
	wish to control. If you are unable to program the TV remote control to
	operate your device or some of the features on that device, use the
	deviceÕs remote control or the controls on the device.		POWER
¥	Each time you change the batteries you will need to reprogram the
	remote control.		Numbers
¥	Some newer VCRs respond to either of two codes. These VCRs have a		MODE
	switch labeled ÒVCR1/VCR2.Ó If your VCR has this kind of switch and
	does not respond to the codes for your VCR brand, set the switch to the
	other position (ÒVCR1Ó or ÒVCR2Ó) and reprogram the remote control.
			y
			CH y
			VOL y
			RECALL

		Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.	33
#01E_028-036_4250HP95	33	05.9.12, 10:06 PM
	Black

(E) 42/50HP95 *web 213:276