Function Code List (cont.)
|
|
| Function | |
|
|
| ||
| Remote Controller | 24 hour or 12 hour remote control display. | ||
| ||||
| Indication | 0=24hr; 1=12hr | ||
|
|
|
| |
| Outdoor Night Time | 0 | = Function invalid | |
| 1 | = Function valid | ||
| Low Noise |
|
| |
Start time (hour) | ||||
| Operation | |||
| End time (hour) | |||
|
| |||
|
|
| ||
| Alarm Tone | Tone Switching 0: OFF, 1: ON | ||
|
|
|
| |
| Pump P2 remote | 0 | = Not Shown; | |
| controller Display | 1 | = Shown | |
|
|
|
| |
| Outdoor Forced | 0 | = Forced Defrost OFF; | |
| Defrost Mode | 1 | = Forced Defrost ON | |
|
|
|
| |
| Optional ON/OFF | 0 | = a contact “ON” = Forced stop | |
| 1 | = b contact “OFF” = Forced stop | ||
| Command | 2 | = ON/OFF = Start / Stop | |
|
| 3= HA Specification | ||
| Outdoor Night Time | 0 | = Symbol displayed when mode is valid | |
| (controlled by Function Code Only); | |||
| Mode Button | 1 | = Symbol displayed when mode is activated | |
|
| (controlled by Function Code and Button) | ||
| Control Logic for | 0 | = Cooling thermo on – contact open; | |
| Room Thermostat | 1 | = Cooling thermo on – contact close |
Quick Reference Guide - Page 26
Function Code Number |
|
| ||
|
|
|
| |
Hydro Unit | Remote | Range | Default | |
Controller | ||||
|
|
| ||
|
|
|
| |
- | 05 | 0 ~ 1 | 0 | |
|
|
|
| |
- | 09 | 0 ~ 1 | 0 | |
|
|
|
| |
- | 0A | 0 ~ 23 | 22 | |
- | 0B | 0 ~ 23 | 06 | |
|
|
|
| |
| 11 | 0 ~ 1 | 1 | |
|
|
|
| |
42 | - | 0 ~ 1 | 0 | |
|
|
|
| |
46 | - | 0 ~ 1 | 0 | |
|
|
|
| |
52 | - | 0 ~ 3 | 0 | |
|
|
|
| |
56 | - | 0 ~ 1 | 0 | |
|
|
|
| |
57 | - | 0 ~ 1 | 0 | |
|
|
|
|
Settings by Purpose
Settings when hot water supply function is not used
• When the hot water supply function is not used, set DIP
Setting for cooling
•For Space Conditioning Units that do not perform cooling (radiators and Under floor heating, etc.), procure a motorized
•Press long the TEST + SET + SELECT switches on the remote controller to change the Hydro Unit function code, and change address 02 to 0, and then press the SET button to enable the function.
Press the TEST button to exit the setting mode.
• Stick the optional insulator for cooling to the bottom of the Hydro Unit.
Settings for hot water supply
•Prepare the optional hot water cylinder.
•Procure a motorized
•Set DIP
•Connect the power supply unit for the hot water cylinder heater to terminals TB03 L and N of the Hydro Unit.
•Connect cables between the Hydro Unit and the hot water cylinder as follows:
Hydro Unit terminals | TB03 | (1), (2), and earth — | Hot water cylinder (1), (2), and earth |
| TB06 | A, B, and earth — | Hot water cylinder A, B, and earth |