480p (Progressive)
480p (Progressive)
Component
480i (Interlace)
HDMI
OFF
￿￿￿￿￿￿￿ ￿￿￿￿￿%￿&￿''￿(￿￿￿￿￿￿￿'￿￿￿￿￿& 720p (Progressive)￿￿￿￿￿￿￿￿￿￿￿480p￿￿￿￿￿￿￿￿(Progressive)￿￿￿￿!"￿￿￿￿￿￿#￿￿￿￿￿￿￿￿ !$￿￿￿￿￿￿￿￿￿
1080i (Interlace) 480p (Progressive)
The content of the output￿￿￿￿for each ouput jacks are as shown in the following table and differ depending￿￿￿on output setting￿ .￿￿￿￿￿
￿￿￿ ￿￿￿￿￿ ￿￿￿￿￿ ￿￿￿￿ ￿￿￿￿￿ ￿￿￿￿￿￿￿￿￿
* When the HDMI/Progressive is active, it is impossible to output any video images from the Video out jack and S-Video out jack. In this case, press PROG/HDMI repeatedly to switch the HDMI/Progressive output setting to ÒOFFÓ or set the TV to Component input mode/HDMI input mode.
Notes:
¥ PROG/HDMI button is not available during VCR mode.
¥ 720p and 1080i are available when the unit is connected to the HDMI-compatible display.
¥ When the HDMI mode is active, the HDMI indicator ÒHDÓ on the display window will light up.
¥ If the HDMI cable is disconnected when the HDMI mode is active, the HDMI indicator ÒHDÓ on the display window will flash. In this case, press PROG/HDMI repeatedly to switch the HDMI output setting to ÒOFFÓ, or connect the HDMI cable again.
¥ When the progressive mode is active, the Progressive indicator Ò Ó on the display window will light up. ¥ When the HDMI mode is active, you cannot use Dubbing function (see pages 78 and 79).
¥ If your TV is not compatible with progressive scan, press and hold the STOP button on the front panel for about 3 seconds to return to normal picture.
1. Turn ON the TV and set to the appropriate input mode (HDMI or Component).
2. Press PROG/HDMI on the remote control to change the video output signals (HDMI/Progres- sive) as below.
HDMI Cable (not supplied)
Notes:
¥ Refer to the ownerÕs manual for the TV to be connected to this recorder for more information concerning HDMI connections.
¥ HDMI is an evolving technology, so it is possible that some devices may not operate properly with this recorder. ¥ No sound will be output from the HDMI OUT jack if the ÒDOLBY DIGITAL OUTPUTÓ is not set to ÒPCMÓ (see
page 32).
Switching the output signals (HDMI/Progressive)
For proper operation, it is recommended that you use as short an HDMI cable as possible.

Connections with the TV or audio component

Connect to a TV with HDMI output

HDMI stands for High Definition Multimedia Interface. HDMI transfers digital audio and uncompressed digital video on a single cable. As a result, audio cables and video cables donÕt need to be connected separately to a device. In addition, HDMI is compatible with HDCP (High Bandwidth Digital Content Protection).

HDMI-compatible display

To HDMI input To HDMI OUT

Introduction

21

2J40101A P12-22

21

3/4/06, 10:43 AM

Page 21
Image 21
Toshiba D-VR5SU owner manual Connect to a TV with Hdmi output