2. Expanded Functions

 

 

 

B

F

E

D

C

B

8

 

7

0

 

 

 

 

Abn

Busy

 

Status

 

0

 

 

 

TermSTS

 

 

 

 

B+1

 

 

 

 

 

 

Transmission error information (if TermSTS is H0B)

 

 

 

Inside the parameter:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Transfer parameter

 

 

S20LP

 

 

Ethernet

 

 

MID (network type)

 

 

2

 

 

 

 

3

 

 

 

 

CH (channel of self-station)

1 or 2 (max. two S20LP’s on T3H)

 

1 to 4 (max. four EN311’s on T3H)

 

 

Target station No.

 

 

1 to 64

 

 

0 (fixed)

 

 

Request command

 

 

0 (fixed)

 

 

H0021: Register read/write

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(for other commands, refer to EN311

 

 

 

 

 

 

 

 

 

 

 

 

 

 

manual)

 

 

Transfer size

 

 

 

 

1 to 128

 

 

1 to 485

 

 

(number of words)

 

 

(max. 84 words for T or C register)

 

(max. 323 words for T or C register)

 

 

 

 

 

 

 

 

 

(designation across T511 and T512 is

(designation across T511 and T512 is

 

 

 

 

 

 

 

 

 

not allowed)

 

 

not allowed)

 

 

Register type

 

 

 

 

H0000: XW/YW register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H0001: W register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H0002: LW register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H0003: RW register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H0004: D register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H0005: F register (CPU)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H∗∗

05: Expanded F register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(IC card, 8k words/bank, ∗∗

is bank No. 01 - 0F)

 

 

 

 

 

 

 

 

 

H∗∗

06: Expanded F register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(IC card, 64k words/bank, ∗∗

is bank No. 01 - 02)

 

 

 

 

 

 

 

 

 

H0007: T register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H0008: C register

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H0009: SW register

 

 

 

 

 

 

 

Leading address

 

 

Designates the leading register address to be transferred

 

 

Response time limit

 

 

Specifies the time limit of the response from target-station. (0.1 s units)

 

 

 

 

 

 

 

 

 

When the bit F is set to ON, the following default value is used.

 

 

 

 

 

 

 

 

 

 

S20LP ...... 4.1 s

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ethernet ... 30 s

 

 

 

 

 

 

 

Target-station IP address

 

 

N/A

 

 

Designates the IP address of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

target-station

 

 

Target-station UDP port No.

 

N/A

 

 

Designates the UDP port No. of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

target-station

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

User’s Manual 67

Page 69
Image 69
Toshiba PROSEC T3H user manual Expanded Functions