Concealed Duct High Static Pressure | Installation Manual |
| ||||
|
|
|
| |||
|
|
|
|
|
|
|
Wired remote |
|
|
|
|
|
|
controller | Main defective parts | Judging device | Parts to be checked / error description | Air conditioner |
|
|
display |
|
| ||||
status |
|
| ||||
Indication |
|
|
|
|
|
|
|
| Network | Address setting, central control remote controller, network adapter |
|
|
|
L20 | LAN communication error | adapter central |
|
| ||
Duplication of address in central control communication |
|
| ||||
|
| control |
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Other outdoor unit error | Entire stop |
|
|
|
|
|
|
|
|
|
L29 | Other outdoor unit error | Outdoor | 1) Communication error between IPDU MCU and CDB MCU |
|
|
|
| Entire stop |
|
| |||
|
|
| 2) Abnormal temperature was detected by the heat sink temp. sensor |
|
| |
|
|
| in IGBT. |
|
|
|
|
|
|
|
|
|
|
L30 | Abnormal external input into | Indoor | External devices, outdoor unit P.C. board | Entire stop |
|
|
indoor unit (interlock) | incorrect external input into CN80 |
|
| |||
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| Operation |
|
|
L31 | Phase sequence error, etc. | Outdoor | Power supply phase sequence, outdoor unit P.C. board | continued |
|
|
phase sequence of the | (thermostat |
|
| |||
|
|
|
|
| ||
|
|
|
| OFF) |
|
|
|
|
|
|
|
|
|
P01 | Indoor unit fan error | Indoor | Indoor fan motor, indoor P.C. board | Entire stop |
|
|
|
|
| thermal relay activated) was detected. |
|
|
|
P03 | Outdoor unit discharge temp. | Outdoor | An error was detected in the discharge temp. releasing control. | Entire stop |
|
|
error |
|
| ||||
|
|
|
|
|
| |
|
|
|
|
|
|
|
P04 | Outdoor unit | Outdoor | Entire stop |
|
| |
system error | detected in the |
|
| |||
|
|
|
|
| ||
|
|
|
|
|
|
|
P05 | Open phase detected | Outdoor | The power supply wire may be connected incorrectly. Check open | Entire stop |
|
|
phase and voltages of the power supply. |
|
| ||||
|
|
|
|
|
| |
|
|
|
|
|
|
|
P07 | Heat sink overheat | Outdoor | Abnormal temperature was detected by the temp. sensor of the IGBT | Entire stop |
|
|
|
|
| heat sink. |
|
|
|
P10 | Indoor unit water overflow | Indoor | Drain pipe, clogging of drainage, float switch circuit, indoor P.C. board | Entire stop |
|
|
| detected |
|
|
|
| |
P15 | Gas leakage detected | Outdoor | There may be gas leakage from the pipe or connecting part. Check for | Entire stop |
| EN |
|
|
| gas leakage. |
|
|
|
|
|
|
|
|
|
|
P19 | Outdoor |
|
| |||
|
| |||||
(Indoor) | due to temperature drop of the indoor unit heat exchanger sensor |
|
| |||
|
| when heating. |
|
| ||
|
|
|
|
|
| |
|
|
|
|
|
|
|
P20 | Outdoor | Entire stop |
|
| ||
operation |
|
| ||||
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Outdoor unit fan motor, outdoor unit P.C. board |
|
|
|
P22 | Outdoor unit fan error | Outdoor | (overcurrent, locking, etc.) was detected in the outdoor unit fan drive | Entire stop |
|
|
|
|
| circuit. |
|
|
|
|
|
|
|
|
|
|
| Outdoor unit inverter Idc |
| IGBT, outdoor unit P.C. board, inverter wiring, compressor |
|
|
|
P26 | Outdoor | circuit protection for compressor drive circuit devices | Entire stop |
|
| |
activated |
|
| ||||
|
| activated. |
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
|
|
P29 | Outdoor unit position error | Outdoor | Outdoor unit P.C. board, | Entire stop |
|
|
position error was detected. |
|
| ||||
|
|
|
|
|
| |
|
|
|
|
|
|
|
P31 | Other indoor unit error | Indoor | Another indoor unit in the group is raising an alarm. | Entire stop |
|
|
|
|
|
| |||
E03/L07/L03/L08 alarm check locations and error description |
|
| ||||
|
|
|
|
| ||
|
|
|
|
|
|
|
: The air conditioner automatically enters the
– 40 – |
|