Toshiba RD-XV48KE owner manual Channel

E3LG0ED_EN.book Page 85 Wednesday, April 30, 2008 11:52 AM

Symptom

Remedy

TV channels cannot be changed.

• Check if the connections are made securely and correctly.

CHANNEL

• Check if the cables are damaged.

• Try “Channel” setting by following the steps on pages 22-23.

Only specific channels do not appear.

• The channels may be set to be skipped. (See page 23.)

The external input channels (such as AV2 or

• This unit does not skip the external input channels. This is not a

AV3) cannot be skipped.

malfunction.

GENERAL

The image from the external device cannot be

• Try pressing [INPUT SELECT F] repeatedly.

displayed.

• Turn on all connected devices.

• Check if the connections are made securely and correctly.

Recording is impossible.

• It is prohibited to make a recording from 2 minutes before the

programmed start time of a timer recording.

• This unit cannot record programmes that contain copy protection signal.

This is not a malfunction.

/ DVD

• The space of the recording media may be used up. Try deleting

unnecessary titles, or exchange it with the recordable media.

• The maximum number of titles or chapters has exceeded. Delete the

HDD

unnecessary titles to make enough space or insert a new recordable

media.

• Check if the connections are made securely and correctly.

Timer recording cannot be performed.

• The internal clock of the unit may have been stopped due to a power

failure that lasted for more than 30 seconds. Reset the clock. (See page

25.)

Recording is impossible.

• Check if the disc is CPRM compatible. Copy-once programmes can only

RECORDING

be copied onto the disc which is CPRM compatible.

• Check if the disc is protected or finalised. Undo the protection or the

finalisation.

• Video mode DVD-RW once formatted in other unit cannot be recorded in

this unit unless formatted in this unit.

• Check if the connections are made securely and correctly.

“Repairing” appears on the TV screen.

• If there is a power failure or unplugging during recording, finalising,

formatting or editing (even after “Repairing” disappears), a repairing

Repairing

process will begin automatically just after turning the unit on again.

DVD

• It may take several minutes up to about several hours.

In a case you intend to cancel the repairing

• If you intend to cancel the repairing process, press [A OPEN\CLOSE]

process.

on the front panel, then select “Yes” and press [ENTER]. After that,

press [OPEN\CLOSE A] to take out the disc. The disc cancelled during

Do you want to cancel a repairing

the repairing process MAY NOT work.

process? When selecting “Yes”,

the disc may not be usable.

Yes

No

Repairing

The indication

• “

” may remain on screen for the

Writing to Disc

100%

“

Writing to Disc

100%

” does

maximum of 20 seconds even after it

reached 100%. This is not a

not disappear.

malfunction.

VCR

Recording does not start immediately after

• Make sure the videotape has a recorded tab when you record to a

pressing [REC I].

videotape. If needed, cover the hole with cellophane tape.

TV aspect ratio does not match your TV

• Check “TV Aspect” setting. (See page 78.)

screen.

• A different aspect ratio will be used when the aspect ratio specified by

the disc is not supported by this unit.

Playback picture is distorted.

• During fast forward or fast reverse, playback picture may be distorted.

Colour of the picture is abnormal.

This is not a malfunction.

• Connect to TV directly. When you connect this unit with the television via

VCR or other devices, the picture may be distorted due to the copy-

protection signal.

PLAYBACK

GENERAL

• Check if the cables are damaged.

• Keep the equipment which may cause electrical disturbances, such as a

cellular phone, away.

There is no sound, or no subtitle.

• Turn on all connected devices.

• Check if the external input channel is set correctly.

• Check if the connections are made securely and correctly.

• If using the HDMI connection, sound is not output when “HDMI Audio” is set to “OFF”.

• Check the RCA audio cable connection. If you are using HDMI-DVI conversion cable, you must connect the RCA audio cable, too.

• If using the HDMI connection, check whether the output format of this unit (HDMI FORMAT) matches the supported input format of other connected device.

EN 85

Introduction Connections Basic Setup Recording Playback Editing Function Setup VCR Functions Others