Trane RT-SVX10C-EN specifications See VOM Contacts -16 Figure

Return Air Humidity Sensor (3U64)		8
return air temperature reaches 135 F		10
Rooftop Module		7
RTM Resistance Input vs Setpoint Temperatures		7
RTM Resistance Value vs System Operating Mode		7
S
Sample Model Number		4–5
Sample Operator's MaintenanceLog		110
See Table 5-8
Saturated Condenser Temperature Sensors		9
saturated condensing temperature falls		9
Scroll Compressor Replacement		105
See Figure 5-2
Service Test Guide for Component Operation		61
See Table 4-1
"Shipwith" Locations		11
Sizing Natural Gas Pipe Mains & Branches		33
See Table 3-4
some fans are rotating backwards		63
See Fan Rotation
Space Pressure Transducer		10, 31
See Figure 3-9
Status/Annunciator Output		9
Steam or Hot Water Coils	36, 37, 109
See Coil Cleaning; Figure 3-12: Figure 3-13:
"Wet Heat"
Suction Line Filter/Drier Installation		105
See Figure 5-2
suction pressure approaches 7 ± 4 psig		9
suction pressure exceeds 22 ± 4 psig		9
supply air temperature falls 10 F below		10
Supply Air Temperature Low Limit		10
supply air temperature reaches 10 F above		10
supply air temperature reaches 240 F		10
Supply Air Temperature Sensor (3RT9)		8
Supply Air Tempering		10
Supply and Exhaust Airflow Proving Switch		8
Supply and Exhaust Fan Circuit Breakers		9
Supply and Exhaust Fan Shipping Channels		30
See Figure 3-8
Supply and Exhaust Fan VFD Programming
Parameters		106
See Table 5-8
Supply Duct Static Pressure Control		11
swing-check vacuum breaker		37
See Figure 3-13
T
"temporary low limit suppression" setting		9
Thermostatic Expansion Valves		83
Trane Communications Interface Module		7
Trane OIL-42		83
Transducer Voltage Output vs Pressure Input		10
TraqTM Sensor Airflow Measurement		66
Two Stage Gas Furnace		56
Typical Field Power Wiring		39
See Figure 3-14
Typical Field Wiring Diagram		49-53
See Figure 3-16: Figure 3-17
Typical Gas Furnace		99
See Figure 4-10
Typical Ventilation Override Binary
Output Wiring		50-53

See VOM Contacts: FIgure 3-16: Figure 3-17
U
unit and curb operating weights	22
See Table 3-3
Unit Internal Fuse Replacement Data & VFD
Factory Settings	101
See Table 5-3
units electric heat units operating on 460/575 vol	39
See Figure 3-14
units operating on 200/230 volts	38
units operating on 460/575 volts	38
Units with an Economizer	55
Units with TraqTM Sensor	55
Units without an Economizer	55
Unoccupied Heating	11
unoccupied to an occupied mode with
the MWU option	10
V
Variable Air Volume Systems	65
VAV Changeover Contacts	46
VAV Control Option	49-53
See Figure 3-16: Figure 3-17
VCM optional CO2 sensor	8
VCM optional temperature sensor	8
Velocity Pressure Transducer/Solenoid Assembly	8
Ventilation Control Module	8
Ventilation Override Module	7
VFD Programming Parameters	106
See Table 5-8
Voltage Imbalance	60
Voltage Supply	60
VOM Contacts	47
See VOM Modes
VOM Mode “A”	47
See VOM Contacts
VOM Mode “B”	47
See VOM Contacts
VOM Mode “C”	47
See VOM Contacts
VOM Mode “D”	47
See VOM Contacts
VOM Mode “E”	47
See VOM Contacts
W
Warnings	6
Wet Airside Pressure Drop	70-72
See Figure 4-3
Wet Heat	58
“Wet” heatactuator	58
"Wet Heat" Coil Fin Data	102
See Table 5-5
Z
Zone Temperature - Cooling	10
Zone Temperature - Heating	10

113