Dimensions &

Weights VFD

Variable Frequency Drive Option (VFD)

￿WARNING

Control and LineVoltage!

Control and line voltage wiring from the VFD to the unit must be in accordance with all local and National Electric Codes. Do not touch circuit components until main power has been turned off and “charge” lamp is extinguished.The capacitors are still charged and could

result in death or serious injury.

Mounting Requirements

Proper location of theVFD is important to achieve proper performance and normal operating life. Installation must be in an area where it will be protected from:

•Direct sunlight, rain or moisture.

•Corrosive gases or liquids.

•Vibration, airborne dust, or metallic particles.

For effective cooling as well as proper maintenance, install theVFD vertically to the ground using four mounting screws.

There must be a minimum eight inch clearance above and below theVFD. A minimum two inch clearance is required on each side.

Also, allow enough clearance for opening theVFD cabinet door.This will ensure sufficient air space for cooling.

Refer to the “Dimensions andWeights” section beginning on page 19 forVFD dimensions and weights.

￿WARNING

HazardousVoltage w/Capacitors!

Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/tagout proce- dures to ensure the power cannot be inadvertently energized. For variable frequency drives or other energy storing components provided byTrane or others, refer to the appropriate manufacturer’s literature for allowable waiting periods for discharge of capacitors.Verify with an appropriate voltmeter that all capacitors have discharged. Failure to disconnect power and discharge capacitors before servicing could result in death or serious injury.

Note: For additional information regard- ing the safe discharge of capacitors, see

PROD-SVB06A-EN or PROD-SVB06A-FR.

NOTICE

Use Copper Conductors Only!

Unit terminals are not designed to accept other types of conductors. Failure to use copper conductors may result in equipment damage.

The variable frequency drive (VFD) option can only be used with IntelliPak units.The VFD andVFD w/bypass is available from

5to 25 hp and is aTraneTR1. AllVFD’s are pre-configured and run tested at the factory prior to shipping.TheVFD is wall mounted.

A

B

G

F

C

ED

VFD dimensions, in.

voltage

hp

A

B

C

D

E

F

G

460

7.5

15.55

15.12

7.87

8.66

0.39

0.24

7.87

 

10

 

 

 

 

 

 

 

208

7.5

22.05

21.26

7.87

9.53

0.83

0.30

10.24

 

10

 

 

 

 

 

 

 

46015

20

25

208

15

27.56

26.77

10.63

12.13

0.83

0.30

11.05

 

20

 

 

 

 

 

 

 

46030

40

208

30

31.50

30.71

10.63

12.13

0.75

0.30

11.65

460

50

 

 

 

 

 

 

 

 

60

 

 

 

 

 

 

 

208

40

31.49

30.71

10.63

14.57

1.97

-

13.19

28

SCXG-SVX01B-EN

Page 27 Page 29
Page 28
Image 28
Trane SCXG-SVX01B-EN manual Dimensions Weights VFD, Variable Frequency Drive Option VFD, Control and LineVoltage
Page 27 Page 29

SCXG-SVX01B-EN specifications

The Trane SCXG-SVX01B-EN is an advanced variable refrigerant flow (VRF) system designed to provide efficient and flexible heating and cooling solutions for commercial and residential applications. This system exemplifies Trane's commitment to innovation, energy efficiency, and ease of installation, making it a standout choice in the industry.

One of the main features of the SCXG-SVX01B-EN is its ability to deliver precise temperature control across multiple zones. The system utilizes a modular design that allows for the connection of multiple indoor units to a single outdoor unit, enabling simultaneous heating and cooling in different areas of a building. This zoned comfort not only enhances occupant satisfaction but also contributes to energy savings by allowing for targeted climate control where it is most needed.

Trane's VRF technology is complemented by its inverter-driven compressors, which adjust their speed according to the demand for heating or cooling. This means that the system operates more efficiently than traditional systems by consuming less energy during partial load conditions. The SCXG-SVX01B-EN also integrates advanced heat recovery capabilities, allowing it to transfer heat from one zone to another, further optimizing energy usage.

The unit's compact design simplifies installation, making it suitable for both retrofit projects and new constructions. The flexible piping layout supports various configurations, allowing easy adaptation to the building's architecture. The model also incorporates intelligent controls, offering a user-friendly interface that enhances operational flexibility and promotes energy management.

In addition to its performance features, the Trane SCXG-SVX01B-EN emphasizes sustainability. It uses advanced refrigerants with low global warming potential (GWP), aligning with environmental regulations and helping to minimize the system's ecological footprint. The durable construction of the system ensures longevity and reliability, reducing maintenance costs and enhancing overall operational efficiency.

Finally, Trane supports its products with comprehensive warranties and a network of service professionals, ensuring that customers have access to expert assistance throughout the life cycle of their system. The SCXG-SVX01B-EN represents a blend of technology, efficiency, and versatility, making it an ideal choice for those seeking an effective heating and cooling solution.
Top Page Image Contents