pre-startup

Installation requirements

Airside Economizer

Installation

Note: Airside economizer option available on

20-80 tons only.

Unit Handling

1.Hoist the damper cabinet to the installation location with straps positioned under the skid as shown in Figure I-PR-4. Use spreader bars to prevent unit damage during lifting.

2.With the damper cabinet at its final location (near the unit), remove the screws securing it to the skid from the side flanges. Retain these screws for later use.

Unit Preparation

Figure I-PR-4. Proper lifting of the airside economizer

3.The support legs are secured to the skid, and the hanging bracket is secured with wire ties to an inside flange near the cabinet’s base. Remove the C- channel collar and install it on the unit, if not already installed.

4.Remove the roll of 1/8” thick gasket from the damper cabinet’sW-supports, and apply it to the C-channel collar mounted on the rear of the unit. This gasket will provide a seal between the damper cabinet and the unit.

5.Attach the legs (with screws provided) to the leg brackets located on the damper’s base.

6.Attach a field-provided clevis of suitable strength ( > 1/2” ), to each of the corner lifting brackets through the

7/8” diameter holes.

7.Attach to the clevises a means of lifting the damper cabinet from its skid.

Unit Installation

o’clock, and secure it with screws provided. See Figure I-PR-5.

10.Lift the damper cabinet and position it such that the hanging bracket is positioned over the unit’s C-channel collar.

11.Lower the damper cabinet until the holes in its side flanges are aligned with the holes in the C-channel collar. Install screws removed in step 3 through the damper cabinet’s side flanges and into the C-channel’s corresponding holes.

12.Attach ductwork to the top and back dampers according to local codes.

Field Wiring Connections

13.Open the damper cabinet’s door and connect the factory-provided plug from the actuator to the factory-provided plug in the unit’s filter section.

14.Cabinets with TRAQ dampers only: Unroll the two rolls of pneumatic tubing located inside the damper cabinet. Route these tubes through the cabinet’s front upper panel (0.25 dia. holes provided). Connect them to the two pneumatic tubes protruding from the customer electrical connection panel on the unit. Be sure to connect like tubes to each other (black to black, white stripe to white stripe).

15.Cabinets with TRAQ dampers only: Locate the “bullet” sensor and rolled up wiring in the unit’s filter section. Route it into the damper cabinet and insert the sensor into the sensor mounting clip attached to underside of one of theTraq dampers.

8.Slowly raise the damper cabinet from its skid.

9.Attach the hanging bracket across the front of the damper cabinet. Position it with its short flange pointing to four

Airside

Economizer

Figure I-PR-5. Proper installation of the airside economizer option

SCXG-SVX01B-EN

37

Page 37
Image 37
Trane SCXG-SVX01B-EN manual Airside Economizer Installation, Unit Handling, Unit Preparation, Unit Installation

SCXG-SVX01B-EN specifications

The Trane SCXG-SVX01B-EN is an advanced variable refrigerant flow (VRF) system designed to provide efficient and flexible heating and cooling solutions for commercial and residential applications. This system exemplifies Trane's commitment to innovation, energy efficiency, and ease of installation, making it a standout choice in the industry.

One of the main features of the SCXG-SVX01B-EN is its ability to deliver precise temperature control across multiple zones. The system utilizes a modular design that allows for the connection of multiple indoor units to a single outdoor unit, enabling simultaneous heating and cooling in different areas of a building. This zoned comfort not only enhances occupant satisfaction but also contributes to energy savings by allowing for targeted climate control where it is most needed.

Trane's VRF technology is complemented by its inverter-driven compressors, which adjust their speed according to the demand for heating or cooling. This means that the system operates more efficiently than traditional systems by consuming less energy during partial load conditions. The SCXG-SVX01B-EN also integrates advanced heat recovery capabilities, allowing it to transfer heat from one zone to another, further optimizing energy usage.

The unit's compact design simplifies installation, making it suitable for both retrofit projects and new constructions. The flexible piping layout supports various configurations, allowing easy adaptation to the building's architecture. The model also incorporates intelligent controls, offering a user-friendly interface that enhances operational flexibility and promotes energy management.

In addition to its performance features, the Trane SCXG-SVX01B-EN emphasizes sustainability. It uses advanced refrigerants with low global warming potential (GWP), aligning with environmental regulations and helping to minimize the system's ecological footprint. The durable construction of the system ensures longevity and reliability, reducing maintenance costs and enhancing overall operational efficiency.

Finally, Trane supports its products with comprehensive warranties and a network of service professionals, ensuring that customers have access to expert assistance throughout the life cycle of their system. The SCXG-SVX01B-EN represents a blend of technology, efficiency, and versatility, making it an ideal choice for those seeking an effective heating and cooling solution.