Reg | Transcend Information TS32M~1GCF80 instruction

TS32M~1GCF80					80X CompactFlash Card


-REG			I	44	This signal is used during Memory Cycles to distinguish between Common
(PC Card Memory Mode)					Memory and Register (Attribute) Memory accesses. High for Common Memory,
Attribute Memory Select					Low for Attribute Memory.
-REG					The signal shall also be active (low) during I/O Cycles when the I/O address is
(PC Card I/O Mode)					on the Bus.

-DMACK					This is a DMA Acknowledge signal that is asserted by the host in response to
(True IDE Mode)					DMARQ to initiate DMA transfers.
					While DMA operations are not active, the card shall ignore the -DMACK signal,
					including a floating condition.
					If DMA operation is not supported by a True IDE Mode only host, this signal
					should be driven high or connected to VCC by the host.
					A host that does not support DMA mode and implements both PCMCIA and
					True-IDE modes of operation need not alter the PCMCIA mode connections
					while in True-IDE mode as long as this does not prevent proper operation all
					modes.

	Signal Name		Dir.	Pin	Description

RESET			I	41	The CompactFlash Storage Card is Reset when the RESET pin is high with the
(PC Card Memory Mode)					following important exception:
					The host may leave the RESET pin open or keep it continually high from the
					application of power without causing a continuous Reset of the card. Under
					either of these conditions, the card shall emerge from power-up having
					completed an initial Reset.
					The CompactFlash Storage Card is also Reset when the Soft Reset bit in the
					Card Configuration Option Register is set.
RESET					This signal is the same as the PC Card Memory Mode signal.
(PC Card I/O Mode)
-RESET					In the True IDE Mode, this input pin is the active low hardware reset from the
(True IDE Mode)					host.
(True IDE Mode)

VCC			--	13,38	+5 V, +3.3 V power.
(PC Card Memory Mode)
VCC					This signal is the same for all modes.
(PC Card I/O Mode)
VCC					This signal is the same for all modes.
(True IDE Mode)

Transcend Information Inc.					11
					V1.1

Image 11

Transcend Information TS32M~1GCF80 dimensions Reg

Contents

80X CompactFlash Card Placement FeatureDimensions Description CHS and Capacity Ordering Information Compactflash Card Specification Block Diagram Electrical Interface Pin Assignment and Pin Type PC Card Memory Mode PC Card I/O Mode True IDE Mode4 V1.1 Signal Name Dir Pin Description Signal Description Csel V1.1 Iord REG True IDE Mode As Iordy Input Leakage Current Electrical Specification Parameter Symbol Min Max Unit Remark Input Characteristics CompactFlash interface I/O at Min Max Unit Parameter Output Drive Type Output Drive Characteristics Signal Card Host Signal Interface 150 μ a high state per socket TS32M~1GCF8080X CompactFlash Card Attribute Memory Read Timing Figure Attribute Memory Read Timing Diagram Configuration Register Attribute Memory Write Timing Min Max Symbol Common Memory Read Timing SpecificationCycle Time Mode 250 ns 120 ns 100 ns 80 ns Min Symbol Common Memory Write Timing Specification 80X CompactFlash Card I/O Input Read Timing Specification Cycle Time Mode 255 ns 120 ns 100 ns 80 ns 10 I/O Output Write Timing Specification Mode True IDE PIO Mode Read/Write Timing Specification V1.1 True IDE Multiword DMA Mode Read/Write Timing Specification A10 A8-A4 Card ConfigurationMultiple Function CompactFlash Storage Cards CE2 CE1 CE2 CE1 A10 D15-D8 D7-D0 Function ModeAttribute Memory Function Configuration Option RegisterBase + 00h in Attribute Memory Table CompactFlash Storage Card Configurations Table Pin Replacement Changed Bit/Mask Bit Values Pin Replacement Register Base + 04h in Attribute Memory I/O Transfer Function Socket and Copy Register Base + 06h in Attribute Memory Function Code True IDE Mode I/O Transfer FunctionTable Pcmcia Mode I/O Function Common Memory Transfer Function V1.1 CF-ATA Drive Register Set Definition and Protocol Table I/O Configurations Table Primary and Secondary I/O Decoding I/O Primary and Secondary Address Configurations Table Contiguous I/O Decoding Contiguous I/O Mapped Addressing Memory Mapped Addressing Data Register Address 1F0h170hOffset 0,8,9 True IDE Mode AddressingCF-ATA Registers Table Data Register Access Error Register Address 1F1h171h Offset 1, 0Dh Read Only Cylinder Low LBA 15-8 Register Address 1F4h174h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Sector Number LBA 7-0 Register Address 1F3h173h Offset Figure Status & Alternate Status Register Device Control Register Address 3F6h376h Offset Eh Figure Device Control Register Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Description LBA CF-ATA Command Set Definitions Cyl High Cyl Low Sec Num Sec Cnt Feature Check Power Mode 98h or E5hExecute Drive Diagnostic 90h Bit Command Sec Num LBA Sec Cnt Erase Sectors C0hFormat Track 50h Drive Head LBA Cyl High Bytes Word Default Total Data Field Type InformationIdentify Device Ech Total Data Field Type Information Word 6 Default Number of Sectors per Track Word 0 General ConfigurationWord 1 Default Number of Cylinders Word 3 Default Number of Heads Total Sectors Addressable in LBA Mode Word 49 Capabilities Bit 13 Standby TimerPIO Data Transfer Cycle Timing Mode Multiple Sector Setting Recommended Multiword DMA transfer cycle time Multiword DMA transferWord 64 Advanced PIO transfer modes supported Word 65 Minimum Multiword DMA transfer cycle time Word 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedWords 85-87 Features/command sets enabled Word 128 Security Status Bit 8 Security Level Word 91 Advanced power management level valueWord 89 Time required for Security erase unit completion Additional Requirements for CF Advanced Timing Modes Word 160 Power Requirement DescriptionValue Maximum PIO mode timing selected Value Maximum Pcmcia IO timing mode Supported Value Maximum Multiword DMA timing mode supportedValue Current PIO timing mode selected Value Current Multiword DMA timing mode selected Initialize Drive Parameters 91h Drive Cyl High Cyl Low Sec Num Sec Cnt FeatureIdle 97h or E3h Idle Immediate 95h or E1h Read DMA C8h Read Buffer E4h Read Multiple C4h Read Verify Sectors 40h or 41h Read Sectors 20h or 21h Request Sense 03h Recalibrate 1Xh Seek 7Xh Table Extended Error Codes Table Feature Supported Set Features EFh Set Multiple Mode C6h Standby 96h or E2h Set Sleep Mode- 99h or E6h TableTranslate Sector Information Standby Immediate 94h or E0hTranslate Sector 87h Write DMA CAh Wear Level F5hWrite Buffer E8h Write Multiple Command C5h Write Sectors 30h or 31h Write Multiple without Erase CDh Write Verify 3Ch Write Sectors without Erase 38h BBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERR 80X CompactFlash Card Error Posting CIS Description Address Data Description of Contents CIS function Address Data 5 4 Description of Contents CIS function Cistplconfig V1.1 MS IR IO RO a Address Data 5 4 3 2 1 Description of Contents CIS function Irqn LS AS NR RO a T