Installing the Processor and Heatsink | Tyan Computer S2498 specs

Once the memory modules are firmly seated in the slot, two latches on either side will close and secure the module into the slot. Sometimes you may need to close the latches yourself.

To remove the memory module, simply push the latches outwards until the memory module pops up. Then simply remove the module.

Due to the PCI v2.2 specifications, you MUST unplug the power connector to the

NOTE motherboard before performing system hardware changes to avoid having your motherboard boot-up automatically.

2.16 – Installing the Processor and Heatsink

Your brand new Tomcat K7M supports the latest processor technologies from AMD. Check TYAN’s website for latest processor support:

http://www.TYAN.com

The following diagrams will detail how to install your processor:

The processor you choose to use may not look exactly like the one pictured above, nor will the socket look exactly the same. For example, your processor may appear to be in a different color and have different markings on it. The diagram is provided as a visual guide to help you install the processor.

1.Lift the lever on the socket until it is approximately 90o or as far back as possible to the socket.

18

http://www.TYAN.com

Image 18

Tyan Computer S2498 manual Installing the Processor and Heatsink

Contents

Tomcat K7M Table of Contents Before you begin… Check the box contents Introduction Form Factor PowerRegulatory OS Operating System Support Board Installation InstallationHow to install our products right…. the first time Board Image S2498 Tomcat K7M Block Diagram Block Diagram Board Parts, Jumpers and Connectors JP7, *JP15 JP13JP8, JP14 J37 PIN Cmos Cmos Reset JP13Default S/PDIF Header J1 USB Header JP2 Audio Header J5 LAN1 LED Header JP8, JP14 10 *LAN2 LED Header *JP7, *JP15, *JP16 Internal Audio Connector Cdin VGA Header J37 Mounting the Motherboard Installing the Memory = 9 Chips Memory Installation Procedure Installing the Processor and Heatsink Finishing Installing the Heatsink Attaching Drive CablesPage Page Installing Add-In Cards Connecting External Devices Installing the Power SupplyDisconnect power supply from electrical outlet Finishing Up Setup Basics Bios SetupStarting Setup Key Function Case of Problems Setup VariationsGetting Help Main Bios Setup Save & Exit Setup Load Optimized DefaultsSupervisor / User Password Exit Without Save Date / Time Setup Standard Cmos FeaturesPhoenix AwardBIOS Cmos Setup Utility Standard Cmos Features IDE Master / Slave Setup Video Halt On Advanced Bios Features Typematic Rate Setting Boot Up Floppy SeekBoot Up NumLock Status Typematic Delay Msec Boot Other Device Hard Disk Boot PriorityFirst / Second / Third Boot Device Small Logo EPA Show Memory Hole： Advanced Chipsets FeaturesSystem Bios Cacheable Video RAM Cacheable Dram Clock Current FSB FrequencyCurrent Dram Frequency Dram Timing AGP Mode Dram Command RateWrite Recovery Time Active to CMD Trcd AGP Fast Write CPU Direct Access FBTVConnector AGP Master 1 WS Write PCI1/PCI2 Master 0 WS Write Phoenix AwardBIOS Cmos Setup Utility CPU & PCI Bus ControlPCI Delay Transaction PCI1/PCI2 Post Write Integrated Peripherals Phoenix AwardBIOS Cmos Setup Utility Integrated PeripheralsVIA OnChip IDE Device Phoenix AwardBIOS Cmos Setup Utility Init Display First IDE HDD Block Mode Sata ModeIDE Prefetch Mode VIA OnChip PCI Device Phoenix AwardBIOS Cmos Setup Utility Onchip USB Controller AC97 AudioMC97 Modem OnChip Ehci Controller IR Transmission Delay Super IO Device Phoenix AwardBIOS Cmos Setup UtilityUart Mode Select UR2 Duplex Mode EPP Mode Select Use IR PinsParallel Port Mode ECP Mode Use DMA Power Management Setup Run Vgabois if S3 Resume Modem Use IRQSoft-Off by Pwrbtn Ac Loss Auto Restart USB Resume from S3 PowerOn by PCI CardRTC Alarm Resume PCI Master Primary Intr IRQ8, 9, 10, 11IRQ3,4, 5, 6, 7, 12, 13 PnP/PCI Configurations Shutdown Temperature Phoenix AwardBIOS Cmos Setup Utility PC Health StatusCPU Warning Temperature PC Health Status Spread Spectrum Frequency/Voltage ControlAuto Detect PCI Clk CPU Clock Load Fail-Safe Defaults Y/N? N Load Fail-Safe DefaultsLoad Optimized Defaults Load Optimized Defaults Y/N? N Supervisor/User Password Setting Enter Password Password Disabled Save to Cmos and Exit Y/N? Y Exit Without Saving Phoenix AwardBIOS Cmos Setup Utility Quit without saving Y/N? Y Diagnostics Memory, Video, CPU Beep CodesFlash Utility Appendix I Glossary Page Mirroring see RAID Page Page Returning Merchandise for Service Technical Support Document # D1650-101