Manuals / Unitech / Computer Equipment / Barcode Reader

Unitech RS700 Controlling Smart-Reader Server Remotely, Making RFID Applications, Srsrc

Models: RS700

1 58

Download 58 pages 18.83 Kb

Page 20

Chapter 3 Making RFID Applications

Chapter 3 Making RFID Applications

NOTE: The yellow RFID LED on the RS700’s front panel indicates the Smart- Reader Server status. On means SRS is running. On and flashing means TCP server in SRS is running and waiting for request from SRSRC. On and fast flashing means TCP server is processing requests from SRSRC. Off means SRS is not running. On and not flashing means TCP server in SRS is not running so SRSRC cannot connect to it.

Controlling Smart-Reader Server Remotely

It is necessary to install the Smart-Reader Server Remote Control (SRSRC) Program, to control the built-in RS700 Smart-Reader Server remotely. Please contact a Unitech representative to acquire the program.

SRSRC

Remote Control

SRS

Computer

RS700

Installing Microsoft .NET Framework

To execute the SRSRC, Microsoft .NET Framework 3.5 must be installed on the com- puter. Download the software from the Microsoft Download Center at:

http://www.microsoft.com/downloads/details.aspx?FamilyID=333325fd-ae52-4e35- b531-508d977d32a6&DisplayLang=en.

NOTE: Uninstall any previous versions of Microsoft .NET Framework before installing Microsoft .NET Framework 3.5.

Installing the SRSRC Program

Install the SRSRC program and acquire an IP address for the RS700 through the fol- lowing:

1.Connect the computer to a DHCP enabled network.

2.Connect the Ethernet Cable to the Ethernet Port on the RS700’s bottom panel, and rotate the cable cap clockwise to secure the connection.

3.Connect the RS700 to the same network via DHCP. The DHCP server will assign an IP address to the RS700.

4.Install SRSRC.msi on the computer.

5.Follow the onscreen instructions to complete the SRSRC installation.

6.Click Start → Programs → Smart-Reader Server Remote Control → Reader Discovery.

12

Copyright 2009 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.

Image 20

Unitech RS700 Controlling Smart-Reader Server Remotely, Making RFID Applications, Installing Microsoft .NET Framework

Contents

User’s Manual RS700 Smart RFID Fixed Reader400682G Version Page Preface About This ManualRegulatory Compliance Statements Federal Communication Commission Interference StatementFCC Caution FCC Radiation Exposure StatementBattery Notices Battery Charge NoticeStorage and Safety Notice About This ManualRS700 Smart RFID Fixed Reader - 1-year limited warranty WarrantyUnitech limited Warranty covers the following items Table of Contents Using the HardwarePreface About This ManualAdvanced Settings TroubleshootingSystem Specification Appendix AFeatures Powerful SystemPower Supply ChapterPackage Contents Power CordPower/RS232 Cable Wi-Fi AntennasA Tour of the RS700 Front PanelComponent DescriptionTop Panel Bottom PanelNo. Component DescriptionConnect Power Chapter 1 Getting StartedChapter Using the HardwareInstalling Wi-Fi Antenna Installing RFID Antenna Optional Chapter 2 Using the HardwareUsing the GPIO Interface GPIO Pin AssignmentPin1 Pin NameMounting the RS700 Chapter 2 Using the HardwarePerforming a Hardware Reset Chapter 2 Using the HardwareUsing Smart-Reader Server Making RFID ApplicationsOpening Smart-Reader Server ChapterInstalling Microsoft .NET Framework Installing the SRSRC ProgramControlling Smart-Reader Server Remotely Chapter 3 Making RFID ApplicationsUsing the Smart-Reader Server Remote Control Chapter 3 Making RFID ApplicationsConfiguring Antenna Port Chapter 3 Making RFID ApplicationsDefining Smart Reader Behavior Chapter 3 Making RFID ApplicationsCreating a New EC Spec Chapter 3 Making RFID ApplicationsChapter 3 Making RFID Applications Start //spec1starttrigger Stop //spec1stoptriggerSpecifying Report Criteria Setting up Filter Rules Defining the EC Specurnepcpatgid-96*.*.* to match any GID-96 tag Chapter 3 Making RFID ApplicationsSubscribing the EC Spec Chapter 3 Making RFID ApplicationsRedefining the Subscription Chapter 3 Making RFID ApplicationsViewing Data Collection Report Chapter 3 Making RFID ApplicationsUsing the Application Programming Interface Connecting to BizTalk ServerViewing Server Log Chapter 3 Making RFID ApplicationsChapter 3 Making RFID Applications 3. Right-click Device Providers in the left screen panel, and select New Provider to add a provider. The Add Provider screen appearsChapter 3 Making RFID Applications 5. Click OK to confirm8. Select the newly created provider in Step 4. Click Next 7. Check Add single device. Click NextChapter 3 Making RFID Applications 10. Click Next Chapter 3 Making RFID Applications9. Input the RS700s IP address and port number. Click Next 12. Type a name for the device. Click Next 11. Enter the default user name and password as unitech. Click NextChapter 3 Making RFID Applications Chapter 3 Making RFID Applications 13. Click Finish15. Data collected from the RS700 displays in the Tags field. Setup the interval Chapter 3 Making RFID ApplicationsChapter 3 Making RFID Applications Connecting to Oracle Sensor Edge Server5. Click MyEdgeServer 6. Click Change dispatcher 9. Click MyEdgeServer → Groups → Default 7. Select Smart Reader Dispatcher. Click Select8. Set the Log Level to All. Click Save Changes Chapter 3 Making RFID Applications12. Type a name for the device. For example, RS700. Click Select 10. Click Add new device 11. Select Smart Reader DeviceChapter 3 Making RFID Applications 13. Click MyEdgeServer → Groups → Default → RS700 16. Click MyEdgeServer → Groups → Default → RS700Chapter 3 Making RFID Applications 15. Restart SES17. Click Start all devices Chapter 3 Making RFID ApplicationsAdvanced Settings Connecting to a LAN NetworkObtaining an IP Address ChapterChapter 4 Advanced Settings Setting the System TimeSetting up Ethernet connection Chapter 4 Advanced SettingsConnecting to a WLAN Network Chapter 4 Advanced SettingsChapter 4 Advanced Settings 4. Enter the WEP keys in the dialog box. Click OkChapter 4 Advanced Settings 7. Select Enable Radio. Scroll down the Active Profile list to select the created profileManaging your Wireless Profiles Chapter 4 Advanced SettingsChapter 4 Advanced Settings Radio Configures radio settings on the right fieldsChapter 4 Advanced Settings Click Logout to exit the RS700 WebConfig ServerInstalling Microsoft ActiveSync Establishing Terminal-PC ConnectionAdditional Capabilities Chapter 4 Advanced SettingsConnecting the terminal to Your Computer Chapter 4 Advanced SettingsChapter 4 Advanced Settings Using Microsoft ActiveSync to Exchange FilesOn the computer, click My Computer → Mobile Device folder Chapter 4 Advanced Settings Using Remote Control5. Click Start → Programs → ActiveSync Remote Display Troubleshooting ProblemSolution ChapterSystem Specification Appendix AAppendix B SupportRegion Web site