Manuals / Unitech / Computer Equipment / Barcode Reader

Unitech RS700 user manual Creating a New EC Spec, Making RFID Applications

Models: RS700

1 58

Download 58 pages 18.83 Kb

Page 24

Image 24

Chapter 3 Making RFID Applications

Creating a New EC Spec

In the All Defined EC Specs field, *specTest1 is defined and subscribed as the default. Create a new event cycle specification through the following:

1. Click New EC Spec. An InputBox screen appears.

2.Input a unique EC Spec name or accept the default at spec1. Click OK, and spec1 appears in the All Defined EC Specs field.

3.In the All Defined EC Specs: field, check Repeat, Period: for the automatic reading mode, and set the following values in milliseconds.

–Repeat, Period: field - Cycle time (5000ms by default).

–Duration: field - Duration for reading data within the cycle time (4500ms by default).

Page 24

Image 24

Unitech RS700 user manual Creating a New EC Spec, Making RFID Applications

Contents

RS700 Smart RFID Fixed Reader 400682G VersionUser’s Manual Page Preface About This ManualRegulatory Compliance Statements Federal Communication Commission Interference StatementFCC Caution FCC Radiation Exposure StatementBattery Notices Battery Charge NoticeStorage and Safety Notice About This ManualWarranty Unitech limited Warranty covers the following itemsRS700 Smart RFID Fixed Reader - 1-year limited warranty Table of Contents Using the HardwarePreface About This ManualAdvanced Settings TroubleshootingSystem Specification Appendix AFeatures Powerful SystemPower Supply ChapterPackage Contents Power CordPower/RS232 Cable Wi-Fi AntennasA Tour of the RS700 Front PanelComponent DescriptionTop Panel Bottom PanelNo. Component DescriptionConnect Power Chapter 1 Getting StartedUsing the Hardware Installing Wi-Fi AntennaChapter Installing RFID Antenna Optional Chapter 2 Using the HardwareUsing the GPIO Interface GPIO Pin AssignmentPin1 Pin NameMounting the RS700 Chapter 2 Using the HardwarePerforming a Hardware Reset Chapter 2 Using the HardwareUsing Smart-Reader Server Making RFID ApplicationsOpening Smart-Reader Server ChapterInstalling Microsoft .NET Framework Installing the SRSRC ProgramControlling Smart-Reader Server Remotely Chapter 3 Making RFID ApplicationsUsing the Smart-Reader Server Remote Control Chapter 3 Making RFID ApplicationsConfiguring Antenna Port Chapter 3 Making RFID ApplicationsDefining Smart Reader Behavior Chapter 3 Making RFID ApplicationsCreating a New EC Spec Chapter 3 Making RFID ApplicationsStart //spec1starttrigger Stop //spec1stoptrigger Specifying Report CriteriaChapter 3 Making RFID Applications Setting up Filter Rules Defining the EC Specurnepcpatgid-96*.*.* to match any GID-96 tag Chapter 3 Making RFID ApplicationsSubscribing the EC Spec Chapter 3 Making RFID ApplicationsRedefining the Subscription Chapter 3 Making RFID ApplicationsViewing Data Collection Report Chapter 3 Making RFID ApplicationsUsing the Application Programming Interface Connecting to BizTalk ServerViewing Server Log Chapter 3 Making RFID ApplicationsChapter 3 Making RFID Applications 3. Right-click Device Providers in the left screen panel, and select New Provider to add a provider. The Add Provider screen appearsChapter 3 Making RFID Applications 5. Click OK to confirm7. Check Add single device. Click Next Chapter 3 Making RFID Applications8. Select the newly created provider in Step 4. Click Next Chapter 3 Making RFID Applications 9. Input the RS700s IP address and port number. Click Next10. Click Next 11. Enter the default user name and password as unitech. Click Next Chapter 3 Making RFID Applications12. Type a name for the device. Click Next Chapter 3 Making RFID Applications 13. Click Finish15. Data collected from the RS700 displays in the Tags field. Setup the interval Chapter 3 Making RFID ApplicationsConnecting to Oracle Sensor Edge Server 5. Click MyEdgeServer 6. Click Change dispatcherChapter 3 Making RFID Applications 9. Click MyEdgeServer → Groups → Default 7. Select Smart Reader Dispatcher. Click Select8. Set the Log Level to All. Click Save Changes Chapter 3 Making RFID Applications10. Click Add new device 11. Select Smart Reader Device Chapter 3 Making RFID Applications12. Type a name for the device. For example, RS700. Click Select 13. Click MyEdgeServer → Groups → Default → RS700 16. Click MyEdgeServer → Groups → Default → RS700Chapter 3 Making RFID Applications 15. Restart SES17. Click Start all devices Chapter 3 Making RFID ApplicationsAdvanced Settings Connecting to a LAN NetworkObtaining an IP Address ChapterChapter 4 Advanced Settings Setting the System TimeSetting up Ethernet connection Chapter 4 Advanced SettingsConnecting to a WLAN Network Chapter 4 Advanced SettingsChapter 4 Advanced Settings 4. Enter the WEP keys in the dialog box. Click OkChapter 4 Advanced Settings 7. Select Enable Radio. Scroll down the Active Profile list to select the created profileManaging your Wireless Profiles Chapter 4 Advanced SettingsChapter 4 Advanced Settings Radio Configures radio settings on the right fieldsChapter 4 Advanced Settings Click Logout to exit the RS700 WebConfig ServerInstalling Microsoft ActiveSync Establishing Terminal-PC ConnectionAdditional Capabilities Chapter 4 Advanced SettingsConnecting the terminal to Your Computer Chapter 4 Advanced SettingsUsing Microsoft ActiveSync to Exchange Files On the computer, click My Computer → Mobile Device folderChapter 4 Advanced Settings Using Remote Control 5. Click Start → Programs → ActiveSync Remote DisplayChapter 4 Advanced Settings Troubleshooting ProblemSolution ChapterSystem Specification Appendix AAppendix B SupportRegion Web site