Operation | Vidikron Model 85 guide

Operation

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD Language. (Currently, only English is supported.)

•Menu Mode: This is the manner in which the OSD menus appear and disappear when you press MENU. Choose one of the following:

0 = No transition; menus abruptly appear and disappear.

1 = Menus fade in and out.

2 = “Checkerboard” dissolve; menus appear and disappear in sections.

3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, and retract in the opposite direction.

•Timeout - Short/Long: These settings control how long the OSD menus stay on screen. Select a time-out period of from 2 to 60 seconds.

•Side Bar Color: This controls the color of the inactive image area. The range is from -100 (black) to 100 (white).

The inactive image area is on either side of the active image area when using the 4:3 aspect ratio (or the entire screen when no incoming video signal is present).

•Film Mode: Enable Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the Vision 85 detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may wish to enable Film Mode to ensure stable processing for that source.

System Reset: To reset ALL controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu.

A confirmation message appears, reminding you to save your settings before you perform the reset, so that you can restore them afterwards. If you have done this, select Confirm to continue with the reset. Otherwise, click Back to cancel.

This action is not undoable. Proceed with caution! Before you perform a Caution System Reset, save ALL settings, including “Custom” ISF Presets (page 56), ISF

Day/Night presets (page 58), Output Shift settings (page 58), Input Names (page 59) and Trigger settings (page 61).

Restore Saved Settings: Following a System Reset, select Restore Saved Settings to apply all previously-saved settings to the projector and VHD Controller.

62	Vidikron Vision 85 Owner’s Operating Manual

Image 74

Vidikron Model 85 manual Operation

Contents

1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Viii Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents 1List of Figures Vision 85 Main Menu 1080i Digital or 1080p Sources Only About This Manual This Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn to Description, Features and Benefits Optional Accessories Vision 85 at a Glance Vision 85 Front/Top/Side/Bottom/Rear View Vertical Lens Shift Vision 85 Rear Panel Wired IR 3.5-mm, mini phono jackRS-232C Input RJ-11 female connector VHD Controller Front Panel VHD Controller Front Panel Hdmi 1 / Hdmi 2 Digital Component Video RCA connectorsVHD Controller Rear Panel Inputs Volt 750 mA Trigger Outputs Power Input 100 to 240 VACVideo 1 / S-VIDEO ComLink RS-232 Output Vision 85 Remote Control Unit VHD Controller/Vision 85 Remote Control Cursor Buttons On / OFFENT Enter Video Memory Preset Buttons ISF NT NightCust VID 1 2 / S-VID 2 5 S-Video Vision 85 Built-In Keypad Not used Operation Remote ControlTo install batteries in the remote control Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 85/CineWide or Vision 85/CineWide Installation Type Installation ConsiderationsProjector Installation Options Projector Calibration Digital 1080i or 1080p signals Projector Model Throw Ratios for the Vision 85 SeriesThrow Range Throw Ratio Vision Position Ceiling InstallationFloor Installation Folded Optics Installing the Optional CineWide Lens Mount 6shows the Vision 85/CineWide with AutoScope motor assembly Vision 85 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation 85/CineWide Vision 85/CineWide with Lens Base Plate Floor Mounting Upright Adjusting the ProjectionMounting the Vision Angle VHD Controller Connector Panel AccessConnections to the Vision 85 and VHD Controller Controller Connecting SourceHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with Digital DTV RGB or Component Video Connections See Figure 12. Digital DTV RGB or Component Video Connections Analog Computer RGB Connections See Figure Personal Computer Composite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Connecting a PC or Automation System to the VHD Controller 15. RS-232 Control System Connection Outputs to External Equipment Connecting an External IR Receiver to the VHD Controller 17 -volt Trigger Output Connection from Projector Turning on the Power Power source Adjusting the Picture Orientation Primary Lens Adjustments Installing and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation Adjustment Vision 85/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 85/CineWide with Attach Lens Mounting Assembly to Lens Motor Carriage Plate 22. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using the On-Screen Menus 4Operation Input Source ISF PresetsService Aspect Ratio Aspect Ratio Main MenuInput Source Aspect Ratio Settings Aspect Ratio Description Picture Surface, eliminating the black bars. Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position ISF Presets Information You must enter a passcode to access the Calibration menu Calibration Gain/Offset Refer to ISF Night Display Color, above Press Menu to exit test pattern mode Service Code Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Language Picture AdjustColor Temp VAC Iris Lamp Power Key ISF Effects of Primary Color Hue Adjustments Picture Adjust Advanced White Balance Options HD/RGB AdjLamp Hours read-onlyRefer to Lamp Hours on Always set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation on Language setting Operation 5Maintenance and Troubleshooting Lamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart To Table Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Command Value Description Min/max Stored? Brightness Command Parameter Value Description Min/max Stored? Hdinputres YES Enter key Serial Communications Vision 85 Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications Dimensions VHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron