Home Theater Calibration Specifications | Vidikron Model 85 instruction

Specifications

Table 7-1. Vision 85 Specifications (continued)

Brightness and Contrast	Cinema Standards Measurement System (CSMS)
(variable, depending on VAC	Specifications
calibration):	-	Brightness: 16.1 to 25.2 foot-Lamberts (fL)
	-	Contrast Ratio (variable, based on lens aperture setting):
		215:1 - 234:1
	These measurements are taken from the projector in a controlled, home
	theater environment. All measurements are made to ANSI/NAPM
	IT7.228-1997 specifications using the Photo Research PR-650
	SpectraColorimeter and Minolta LS-100 Luminance Meter, Video
	Essentials test DVD and a 1.3 gain, 72-inch wide screen. The projector is
	calibrated to a color temperature of 6,500K and has a minimum of 150
	hours of usage.
	The foot-Lambert (fL) is the unit of measurement used in commercial
	movie theaters to express image brightness at the screen surface. The
	Society of Motion Picture and Television Engineers (SMPTE) specifies
	16 fL as the target image brightness for film-based projectors using an
	open gate (without film in the projector). More importantly, today
	SMPTE specifies 12 fL as the target image brightness in Digital Cinema
	theaters. The foot-Lambert measurement is dependent on screen size,
	screen gain and projector light output.
	Home Theater Calibration Specifications
	-	Light Output: 430 - 648 ANSI Lumens
	-	Contrast Ratio (variable, based on lens aperture setting):
		215:1 - 234:1
	These specifications are obtained by calibrating the projector as
	described above for CSMS measurements.
	Industry-Standard Specifications
	-	Light Output: 1600 ANSI Lumens
	-	Contrast Ratio (variable, based on lens aperture setting):
		2700:1 - 3350:1
	These are typical projector brightness and contrast specifications found
	in most companies’ sales literature. Vidikron includes these
	measurements in its literature to allow for direct comparison with other
	manufacturers’ projectors. These measurements are typically taken at
	9,000K to 13,000K to get expected performance data when the projector
	is used in professional, commercial and industrial displays.

Power Requirements:	100 to 240 VAC (auto-sensing), 50/60 Hz, 375 Watts

Operating Environment:	40°F to 95°F (5°C to 35°C), 0% to 90% humidity
	(non-condensing)

Dimensions:	See Figure 7-1

Weight (without lens):	50 lbs. (22.68 kg)

Regulatory Approvals:	Complies with FCC, CE C-Tick

Limited Warranty:	Projector: Two (2) years parts and labor from the date of delivery
	to the end user.
	Lamp: 1000 hours or six (6) months, whichever comes first.

Specifications are subject to change without notice.

84	Vidikron Vision 85 Owner’s Operating Manual

Image 96

Vidikron Model 85 manual Home Theater Calibration Specifications, Industry-Standard Specifications, Power Requirements

Contents

1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Viii Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents 1List of Figures Vision 85 Main Menu 1080i Digital or 1080p Sources Only About This Manual This Manual Using This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn to Description, Features and Benefits Optional Accessories Vision 85 at a Glance Vision 85 Front/Top/Side/Bottom/Rear View Vertical Lens Shift Wired IR 3.5-mm, mini phono jack RS-232C Input RJ-11 female connectorVision 85 Rear Panel VHD Controller Front Panel VHD Controller Front Panel Component Video RCA connectors VHD Controller Rear PanelHdmi 1 / Hdmi 2 Digital Inputs Power Input 100 to 240 VAC Video 1 / S-VIDEOVolt 750 mA Trigger Outputs ComLink RS-232 Output Vision 85 Remote Control Unit VHD Controller/Vision 85 Remote Control On / OFF ENT EnterCursor Buttons Memory Preset Buttons ISF NT Night CustVideo VID 1 2 / S-VID 2 5 S-Video Vision 85 Built-In Keypad Not used Remote Control To install batteries in the remote controlOperation Installation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 85/CineWide or Vision 85/CineWide Installation Considerations Projector Installation OptionsInstallation Type Projector Calibration Digital 1080i or 1080p signals Throw Ratios for the Vision 85 Series Throw Range Throw RatioProjector Model Vision Ceiling Installation Floor InstallationPosition Folded Optics Installing the Optional CineWide Lens Mount 6shows the Vision 85/CineWide with AutoScope motor assembly Vision 85 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation 85/CineWide Vision 85/CineWide with Lens Base Plate Adjusting the Projection Mounting the VisionFloor Mounting Upright Angle Connector Panel Access Connections to the Vision 85 and VHD ControllerVHD Controller Connecting Source Hdmi Connections See FigureController Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with Digital DTV RGB or Component Video Connections See Figure 12. Digital DTV RGB or Component Video Connections Analog Computer RGB Connections See Figure Personal Computer Composite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Connecting a PC or Automation System to the VHD Controller 15. RS-232 Control System Connection Outputs to External Equipment Connecting an External IR Receiver to the VHD Controller 17 -volt Trigger Output Connection from Projector Turning on the Power Power source Adjusting the Picture Orientation Primary Lens Adjustments Installing and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation Adjustment Vision 85/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View Adjustment Vision 85/CineWide withAutoScope Attach Lens Mounting Assembly to Lens Motor Carriage Plate 22. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using the On-Screen Menus 4Operation ISF Presets ServiceInput Source Aspect Ratio Main Menu Input SourceAspect Ratio Aspect Ratio Settings Aspect Ratio Description Picture Surface, eliminating the black bars. Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position ISF Presets Information You must enter a passcode to access the Calibration menu Calibration Gain/Offset Refer to ISF Night Display Color, above Press Menu to exit test pattern mode Service Code Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Picture Adjust Color Temp VAC Iris Lamp PowerLanguage Key ISF Effects of Primary Color Hue Adjustments Picture Adjust Advanced White Balance HD/RGB Adj Lamp Hours read-onlyRefer to Lamp Hours onOptions Always set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation on Language setting Operation 5Maintenance and Troubleshooting Lamp Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution To Table Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Command Value Description Min/max Stored? Brightness Command Parameter Value Description Min/max Stored? Hdinputres YES Enter key Serial Communications Vision 85 Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements Dimensions VHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron