Vidikron Vision 120

Installation

Vidikron Vision Model 120 Installation/Operation Manual 23

PRELIMINARY

3. Remove the Lens Cavity Front Cover.

4. Remove the Rear Lens Cap.

5. Hold the lens assembly with the motor

facing the right side of the Lens Cavity.

Carefully insert the back of the lens

assembly into the hole in the lens flange.

Gently push the lens assembly in until it

is seated flush against the flange and the

motor connectors have seated.

Make sure to route the wire harness in its original position and away

from the moving lens stages and Motor Assembly, to prevent unexpected

disconnection or lens damage.

Caution

Contents

Main Page TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Page VIDIKRON PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Important Safety Instructions Compliance Information Page Page Page Page Page Page Page 1.1 About This Manual 1.2 Using This Manual DANGER! WARNING 1.3 Description, Features and Benefits Page 2.1 Vision 120 at a Glance 2. Controls and Functions 2.2 Vision 120 Rear Panel Page 2.3 VHD Controller Front Panel Page 2.4 VHD Controller Rear Panel 123 4 5 67 8 9 Page Controls and Functions 12 Vidikron Vision Model 120 Installation/Operation Manual 2.5 Vision 120 Remote Control Figure 2-5. Vision 120 Remote Control LIGHT OFF ON SOURCE PICTURE MEMORY ASPECT RATIO Page Page 3.1 Remote Control 3.2 Quick Setup Table 3-1. Installation Overview 3.3 Installation Considerations Table 3-2. Projector Installation Options Table 3-3. Vision 120 Lens Options and Throw Ratios Ceiling Installation Floor Installation Figure 3-4. Horizontal Lens Shift (EXAMPLE ONLY) Table 3-4. Vision 120 Vertical and Horizontal Lens Shift Limits 3.4 Installing the Primary Projection Lens Page 3.5 Installing the Optional CineWide Lens Mount Page Page Page Page Page 3.6 Mounting the Vision 120 3.7 Connections to the Vision 120 and VHD Controller Page Installation Vidikron Vision Model 120 Installation/Operation Manual 33 Digital (DTV) RGB or Component Video Connections: See Figure 3-12 and Figure 3-13. Figure 3-12. Digital (DTV) RGB or Component Video Connections (HD1, HD2) Figure 3-13. Digital (DTV) RGB or Component Video Connections (HD3) Page Page to Automation/ Control System or PC Page Installation Vidikron Vision Model 120 Installation/Operation Manual 39 ASPECT RATIO LIGHTOFF Connecting an External IR Receiver to the VHD Controller INPUTS C SYSTEM CONTROL INTERFACE RS-232 / 485 3.8 Turning on the Power 3.9 Adjusting the Picture Orientation V120 Component RCA 16:9 480I 3.10 Primary Lens Adjustments 3.11 Installing and Adjusting the CineWide Anamorphic Lens Page Page Page Page Wrong Position Correct Position Page Page Operation Figure 4-1. VHD Controller OSD Menu Structure for Vision 120 Input Source Calibration Memory Presets Input Position 7 Table 4-1. Aspect Ratio Settings Table 4-1. Aspect Ratio Settings (continued) Page Page Page Page 7 Page Page Page Page 5.1 Lamp Replacement WARNING 5.2 Filter Replacement 5.3 Troubleshooting Tips Table 5-1. Troubleshooting Chart Page 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax Table 6-1. Serial Commands and Responses Table 6-1. Serial Commands and Responses (continued) Page 7.1 Vision 120 Specifications Table 7-1 lists the Vision 120 specifications. Table 7-1. Vision 120 Specifications Table 7-1. Vision 120 Specifications (continued) 7.2 VHD Controller Specifications Table 7-2 lists the VHD Controller specifications. Table 7-2. VHD Controller Specifications Specifications 74 Vidikron Vision Model 120 Installation/Operation Manual 7.3 Vision 120 Dimensions Figure 7-1 shows the Vision 120 dimensions (all dimensions are in inches). Figure 7-1. Vision 120/CineWide with AutoScope Dimensions 7.4 Supported Timings Table 7-3 lists the signal types supported by each input on the Vision 120. Table 7-3. Supported Signal Timings by Input Table 7-3. Supported Signal Timings by Input (continued)