Installing the Optional CineWide Lens Mount | Vidikron Vision 120

Installation

6.Lock the lens in place by turning the Lens Locking Nut (to the left of the lens) 180 degrees counter-clockwise. (Use a 6.0mm hex wrench.)

7.Remove the Front Lens Cap.

8. Replace the Lens Cavity Front Cover.

9.Re-install the Projector Front Jewelry. Tighten the hex screws at the top and bottom of the jewelry to secure it.

3.5

Installing the Optional CineWide Lens Mount

If you are installing a standard (non-CineWide) Vision 120, skip this step and proceed with Mounting the Vision 120 (page 30).

If you are installing a Vision 120/CineWide, proceed with Installing the Fixed CineWide Base Plate (Vision 120/CineWide) (page 29).

If you are installing a Vision 120/CineWide with AutoScope, proceed as follows to install the AutoScope lens motor.

24	Vidikron Vision Model 120 Installation/Operation Manual

Image 38

Vidikron Vision 120 operation manual Installing the Optional CineWide Lens Mount

Contents

120 Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Important Safety Instructions Compliance Information Declaration of Conformity FCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate Operation Maintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Vision 120 offers these key features and benefits Optional Accessories Controls and Functions Vision 120 at a Glance Vision 120 Rear Panel Vision 120 Rear Panel USB-B DVI-DL Dual-Link VHD Controller Front Panel VHD Controller Front Panel Issue LED DVI-DL DUAL-LINK Output 1080p Service only For future useVHD Controller Rear Panel RS-232/485 Control Port Hdmi I 1 / Hdmi II 2 Digital 10. HD3 Input Vision 120 Remote Control Vision 120 Remote Control Source Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video 169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox Letterbox Operation 3InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 120/CineWide or Vision Installation Type Installation ConsiderationsProjector Installation Options Advantages Considerations Vision 120 Lens Options and Throw Ratios Vertical and Horizontal Ceiling InstallationFloor Installation Position Horizontal Lens Shift Example only Vision 120 Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 120/CineWide with AutoScope motor assembly Remove Vision 120 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 120/CineWide Floor Mounting Upright Ceiling Mounting Inverted Adjusting the ProjectionMounting the Vision Angle Connections to the Vision 120 and VHD Controller Connector Panel AccessConnecting the VHD Hdmi Connections See Figure Connecting SourceController Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with 12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 14. Analog RGB Connections Video/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Connection 16. RS-232 Control System Connection Connecting 12-Volt Trigger Equipment Rear Panel Connecting an External IR Receiver to the VHD ControllerVHD Controller Power source Turning on the PowerAdjusting the Picture Orientation Zoom Primary Lens AdjustmentsFocus Installing and Adjusting the CineWide Anamorphic Lens Plate fixed CineWide 20. Attaching the Anamorphic Lens to the Lens Adapter Ring Too Far Left Correct position Too Far Right Installation Anamorphic Lens Top View Adjusting the Geometry Installation Using the On-Screen Menus 4Operation Input Source Memory PresetsService Aspect Ratio Aspect Ratio Main MenuInput Source 169 Aspect Ratio SettingsDescription Hdtv programs in their native Picture Picture Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Information Memory PresetsMemory Presets Information ISF Day CalibrationCalibration ISF Night OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, above HD Format ServiceService Presets 5Maintenance and Troubleshooting Lamp Replacement Filter Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Input Selection Commands Serial Commands and ResponsesCommand Description Response Aspect Ratio Commands Picture Adjust Commands Command Description Response Image Preset CommandsMenu Navigation Commands Enter or Select button Serial Communications 7Specifications Vision 120 Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications Dimensions VHD Controller Specifications Vision 120 Dimensions Vision 120/CineWide with AutoScope Dimensions Supported Signal Timings by Input Supported Timings Format Resolution Frequency HD 1/HD 2/HD Page Vidikron