Manuals / Brands / TV and Video / Projection Television / Vidikron / TV and Video / Projection Television

Vidikron Vision 120 3.7 Connections to the Vision 120 and VHD Controller

1 92

Download 92 pages, 5.97 Mb

Installation

Vidikron Vision Model 120 Installation/Operation Manual 31

PRELIMINARY

3.7 Connections to the Vision 120 and VHD Controller

Proceed as follows to connect the VHD Controller to the Vision 120, your video sources,

external controller(s) – if present – and AC power.

When connecting your equipment:

• Turn off all equipment before making any connections.

• Use the correct signal cables for each source.

• Ensure that the cables are securely connected. Tighten the thumbscrews on connectors

that have them.

Connector Panel AccessTo access the connector panel, press

the door release button so it pops out.

Turn the knob clockwise or

counter-clockwise and pull gently on it

to open the door.

Connecting the VHD

Controller to the Vision 120

The Vision 120 is designed to receive only digital input signals directly from the companion

VHD Controller/Processor. All signal sources should be connected to the appropriate inputs

on the rear panel of the controller. The signal from the controller is then output to the Vision

120 projector through a DVI-DL (dual-link) cable.

Use a Vidikron DVI Dual-Link (DVI-DL) cable to connect the output of the VHD Controller to

the input of the Vision 120; see Figure 3-7.

Figure 3-10. Connecting the Vision 120 to the VHD Controller

You CANNOT connect a signal source with DVI output directly to the

Vision 120. It MUST be routed through the VHD Controller for proper

operation.

Note

II IIII

TRIGGERS

RS-232 / 485

WIRED

REMOTESERVICE ONLY

SYSTEM CONTROL INTERFACE

HD3 (VGA / Y-Pb-Pr) COMPOSITE S-VIDEO

HD2 (BNC)

VsHs

Pr / RPb / BY / G

HD1 (RCA)

Y / G VsHs

Pr / RPb / B

HDMI

II I

INPUTS

Service port.

Not for user

access

Remove the screw to

pull off the lamp cover.

Remove the screw to

pull off the lamp cover.

L

L

SERVICE PORT

AUTHORIZED

PERSONNEL ONLY

Contents

Main Page TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Page VIDIKRON PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Important Safety Instructions Compliance Information Page Page Page Page Page Page Page 1.1 About This Manual 1.2 Using This Manual DANGER! WARNING 1.3 Description, Features and Benefits Page 2.1 Vision 120 at a Glance 2. Controls and Functions 2.2 Vision 120 Rear Panel Page 2.3 VHD Controller Front Panel Page 2.4 VHD Controller Rear Panel 123 4 5 67 8 9 Page Controls and Functions 12 Vidikron Vision Model 120 Installation/Operation Manual 2.5 Vision 120 Remote Control Figure 2-5. Vision 120 Remote Control LIGHT OFF ON SOURCE PICTURE MEMORY ASPECT RATIO Page Page 3.1 Remote Control 3.2 Quick Setup Table 3-1. Installation Overview 3.3 Installation Considerations Table 3-2. Projector Installation Options Table 3-3. Vision 120 Lens Options and Throw Ratios Ceiling Installation Floor Installation Figure 3-4. Horizontal Lens Shift (EXAMPLE ONLY) Table 3-4. Vision 120 Vertical and Horizontal Lens Shift Limits 3.4 Installing the Primary Projection Lens Page 3.5 Installing the Optional CineWide Lens Mount Page Page Page Page Page 3.6 Mounting the Vision 120 3.7 Connections to the Vision 120 and VHD Controller Page Installation Vidikron Vision Model 120 Installation/Operation Manual 33 Digital (DTV) RGB or Component Video Connections: See Figure 3-12 and Figure 3-13. Figure 3-12. Digital (DTV) RGB or Component Video Connections (HD1, HD2) Figure 3-13. Digital (DTV) RGB or Component Video Connections (HD3) Page Page to Automation/ Control System or PC Page Installation Vidikron Vision Model 120 Installation/Operation Manual 39 ASPECT RATIO LIGHTOFF Connecting an External IR Receiver to the VHD Controller INPUTS C SYSTEM CONTROL INTERFACE RS-232 / 485 3.8 Turning on the Power 3.9 Adjusting the Picture Orientation V120 Component RCA 16:9 480I 3.10 Primary Lens Adjustments 3.11 Installing and Adjusting the CineWide Anamorphic Lens Page Page Page Page Wrong Position Correct Position Page Page Operation Figure 4-1. VHD Controller OSD Menu Structure for Vision 120 Input Source Calibration Memory Presets Input Position 7 Table 4-1. Aspect Ratio Settings Table 4-1. Aspect Ratio Settings (continued) Page Page Page Page 7 Page Page Page Page 5.1 Lamp Replacement WARNING 5.2 Filter Replacement 5.3 Troubleshooting Tips Table 5-1. Troubleshooting Chart Page 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax Table 6-1. Serial Commands and Responses Table 6-1. Serial Commands and Responses (continued) Page 7.1 Vision 120 Specifications Table 7-1 lists the Vision 120 specifications. Table 7-1. Vision 120 Specifications Table 7-1. Vision 120 Specifications (continued) 7.2 VHD Controller Specifications Table 7-2 lists the VHD Controller specifications. Table 7-2. VHD Controller Specifications Specifications 74 Vidikron Vision Model 120 Installation/Operation Manual 7.3 Vision 120 Dimensions Figure 7-1 shows the Vision 120 dimensions (all dimensions are in inches). Figure 7-1. Vision 120/CineWide with AutoScope Dimensions 7.4 Supported Timings Table 7-3 lists the signal types supported by each input on the Vision 120. Table 7-3. Supported Signal Timings by Input Table 7-3. Supported Signal Timings by Input (continued)