Remove | Vidikron Vision 120 manual

Installation

Remove Projector Front Feet: Place the projector upside down on a blanket or other soft surface. Loosen and remove the two front feet on the projector.

Remove

Install Ceiling Mount Adapters/Projector Stands: For ceiling installations, the adapters bring the attachment points for the projector mounting rails (included with the projector ceiling mount kit) from the bottom of the projector up and around the AutoScope lens motor housing. For floor installations (where the projector is upright), the adapters allow the projector to lie flat on the mounting surface.

Using six (6) each of the supplied, M6 x 12mm Pan-Head Phillips screws (item #2), attach the AutoScope Ceiling Mount Adapters/Projector Stands (items #3 and #4) to the projector as shown in Figure 3-7.

26	Vidikron Vision Model 120 Installation/Operation Manual

Image 40

Vidikron Vision 120 operation manual Remove

Contents

120 Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Important Safety Instructions Compliance Information Declaration of Conformity FCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate Operation Maintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Vision 120 offers these key features and benefits Optional Accessories Controls and Functions Vision 120 at a Glance Vision 120 Rear Panel Vision 120 Rear Panel USB-B DVI-DL Dual-Link VHD Controller Front Panel VHD Controller Front Panel Issue LED Service only For future use VHD Controller Rear PanelDVI-DL DUAL-LINK Output 1080p RS-232/485 Control Port Hdmi I 1 / Hdmi II 2 Digital 10. HD3 Input Vision 120 Remote Control Vision 120 Remote Control Picture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-Video Memory Preset Buttons Aspect Ratio Selection Buttons169 Lbox Letterbox Remote Control 3InstallationOperation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 120/CineWide or Vision Installation Considerations Projector Installation OptionsInstallation Type Advantages Considerations Vision 120 Lens Options and Throw Ratios Ceiling Installation Floor InstallationVertical and Horizontal Position Horizontal Lens Shift Example only Vision 120 Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 120/CineWide with AutoScope motor assembly Remove Vision 120 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 120/CineWide Adjusting the Projection Mounting the VisionFloor Mounting Upright Ceiling Mounting Inverted Angle Connecting the VHD Connector Panel AccessConnections to the Vision 120 and VHD Controller Connecting Source ControllerHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with 12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 14. Analog RGB Connections Video/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Connection 16. RS-232 Control System Connection Connecting 12-Volt Trigger Equipment VHD Controller Connecting an External IR Receiver to the VHD ControllerRear Panel Adjusting the Picture Orientation Turning on the PowerPower source Focus Primary Lens AdjustmentsZoom Installing and Adjusting the CineWide Anamorphic Lens Plate fixed CineWide 20. Attaching the Anamorphic Lens to the Lens Adapter Ring Too Far Left Correct position Too Far Right Installation Anamorphic Lens Top View Adjusting the Geometry Installation Using the On-Screen Menus 4Operation Memory Presets ServiceInput Source Aspect Ratio Input Source Main MenuAspect Ratio Aspect Ratio Settings Description169 Hdtv programs in their native Picture Picture Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Memory Presets Memory PresetsInformation Information Calibration ISF Night CalibrationISF Day OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format Presets 5Maintenance and Troubleshooting Lamp Replacement Filter Replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command Syntax6Serial Communications Serial Commands and Responses Command Description ResponseInput Selection Commands Aspect Ratio Commands Command Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select button Serial Communications 7Specifications Vision 120 Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements Dimensions VHD Controller Specifications Vision 120 Dimensions Vision 120/CineWide with AutoScope Dimensions Supported Signal Timings by Input Supported Timings Format Resolution Frequency HD 1/HD 2/HD Page Vidikron