System LEDs, Indication, Port LEDs, Installation | Vixel 335

CHAPTER 2 Installation

Vixel Model 335 Installation & Configuration Guide			CHAPTER 2 Installation


	System LEDs		Indication

	Power	When lit, the switch is plugged in and the internal power
	(green LED)	supply is functional.

	Switch Fault	Indicates that the internal hardware self-test failed. When
	(yellow LED)	lit, the switch will not function. -or-
		Indicates that a fan has stopped operating or the ambient
		temperature has exceeded 45°C. When lit, the switch is still
		functional but requires immediate attention. The LED will
		turn off when the detected condition is corrected.

	Switch Op	Indicates whether the zones are initialized and operational.
	(green LED)	If the Switch Op LED is lit, all zones with inserted devices
		are operational. If the Switch Op LED is blinking in a
		multiple zone configuration, one or more zones are
		operational while others are not. If the Switch Op LED is
		off, no operational zones exist or no devices are attached.

	2 Gb/s	Indicates the current operational speed of the switch. When
	(green LED)	lit, the switch is operating at 2 Gb/s. If unlit, the switch is
		operating at 1 Gb/s.

	Mgmt Present	Indicates that switch management is functioning. If
	(yellow LED)	flashing, indicates that management functionality has failed
		and is not communicating with the switch.

	Enet Active	Indicates Ethernet activity on the switch and is controlled
	(green LED)	through the Ethernet transceiver.

Port LEDs

Port LEDs indicate the current status of the particular port.The switch uses two port

LEDs: SFP Status and Port Bypassed/Port Activity. The Port Bypassed and Port Activity

LEDs share the same yellow/green LED.

Figure 2-3. Port LEDs

7

Image 10

Vixel manual System LEDs, Indication, Vixel Model 335 Installation & Configuration Guide, 3. Port LEDs

Contents

InSpeed Model Managed Storage SwitchINSTALLATION&CONFIGURATION guide Part Number 00041363-001 Rev. A Table of Contents A p p e n d i x e s About This Guide FeaturesCHAPTER 1 Introduction Overview Vixel Model 335 Installation & Configuration Guide Fibre Channel - Arbitrated LoopInSpeed Technology CHAPTER 1 Introduction Unpacking the Switch CHAPTER 2 InstallationInstalling the Switch Small Form-Factor Pluggable SFP Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test CHAPTER 2 Installation Setting Up the Switch Attaching Devices Figure 2-1. Switch features diagram Understanding the Switch’s LEDsPower On System LEDs Indication CHAPTER 2 InstallationSystem LEDs Port LEDs Status PortBypassed Activity Cascading with Non-Overlapping Zones Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Zone Zone Zone Figure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerO v e rv i e w CHAPTER 3 Management Logging On and Off CHAPTER 3 ManagementNavigation Figure 3-1. Web Manager Home Page Resetting the Switch Configuring the SwitchConfiguration Task Location in Web Manager Description System Information SettingsSetting Figure 3-2. System Information Page Network Settings Figure 3-3. System Information Change Settings Page Switch Identification Switch SpeedSwitching Mode Blocking ARB Figure 3-5. Time Information Change Settings Page Downloading the Switch ConfigurationTime Settings Figure 3-4. Time Information Page Firmware Settings Figure 3-6. Firmware Information Page 1. Click Load New Firmware Image 1. Click Change Firmware SettingsEvent Log Messages Figure 3-7. Event Log Messages Page Figure 3-8. FC Switch Information Page FC Switch InformationFigure 3-9. FC Switch Information Page with Highlighted Zones Indication OS InformationDetection Figure 3-10. Ordered Set Information Page RRDY Figure 3-11. Ordered Set Information Page with Highlighted Zones Port Usage InformationFigure 3-12. Received Port Utilization Page Value Figure 3-14. Received Port Utilization Change Settings PageFigure 3-13. Received Port Utilization Page with Highlighted Zones Port Settings Figure 3-15. Port Information Page Figure 3-16. Port Information Page with Highlighted Zones Figure 3-17. Port Information Page with Transceiver Information Mode Figure 3-18. Cascade Information Page Figure 3-19. Cascade Information Page with Highlighted Zones Switch Policy Policy SettingsFigure 3-20. Policies Page To update the switch’s policies Figure 3-21. Policies Change Settings Page Figure 3-23. Non-overlapping Zones Zone SettingsFigure 3-22. Overlapping Zones Figure 3-24. Zone Information Page Overlapping Zones Figure 3-25. Overlapping Zone 1 Information Page Figure 3-26. Overlapping Zone 1 Information Configuration Page Non-Overlapping Zones Note Ports 11 and 12 are Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page always in Zone Highlighted Zones Using the Command Line Interface CLI Connecting to the CLI CLI Command Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling DHCP Requests tftp -i IPaddress PUT filename ramdisk Managing the FirmwareDownloading New Firmware tftp IPaddress Message Action Configuring the Trap Destination Table Option Changing the CLI/Web Password Viewing Management, Policy, and Threshold Settings Policies Policy Settings Threshold Information Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning Actions Changing the Switching Mode Command CHAPTER 3 Management Displaying Ports CHAPTER 3 Management Resetting the Switch to Factory Default Settings Resetting the SwitchResetting the Hardware Viewing the Event Log Overlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10 Technical Support ReferenceCHAPTER 4 Technical CHAPTER 4 Technical Reference Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair If the Mgmt Present LED continues to blink and POST has already Problem Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues Recommended Action Appendixes APPENDIX A Specifications S p e c i f i c a t i o n s Vixel Model 335 Operating Conditions Operating ConditionsAPPENDIX A Specifications Requirement Command CommandsConsole Commands General Commands APPENDIX B CLI Console Commands Action Commands APPENDIX B CLI Console Commands Meaning APPENDIX C Event MessagesEvent Action APPENDIX C Event Messages Event Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages Meaning Event APPENDIX D Cross ReferencesLoop ID-ALPA Arbitrated Loop Physical Addresses APPENDIX E Glossary Enables the switch to be divided into separate environments Index Index