Management, Changing the CLI/Web Password | Vixel 335 instruction

Changing the CLI/Web Password

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Note: If you do not remember your password, call your customer service representative.

Changing the CLI/Web Password

One password is used to access both the Web Manager and the Command Line Interface. You can change the password through the Command Line Interface (CLI) only. The password must be between 6 and 25 characters in length.

To change the password:

1.Type pw at the prompt.

2.Enter the current password (the default password is password).

3.Enter the new password.

4.Confirm the new password by re-entering it.

A message appears confirming that the password was saved and activated.

>pw

enter current password: ********

enter new password	:	******
re-enter new password :		******

The new password is saved and activated.

Viewing Management, Policy, and Threshold Settings

The Management Agent menu displays the current settings for the switch parameters, switch policies, and thresholding. To view the current Management Agent settings and a complete list of commands, type mc at the prompt. The Management Agent Menu appears.

MANAGEMENT AGENT 00-10-9b-01-0c-dd

	Product	: Vixel 335 Managed Storage Switch
	Firmware	: 2.01 (build 79)
	Hardware	: 3
	IP address	: 172.16.71.14
	Netmask	: 255.255.240.0
	Default gateway	: 172.16.64.1
	DHCP	: disabled
	Management URL	: http://172.16.71.14
	POLICIES:
(1)	Smart insertion	: enabled
(2)	Bad zone recovery	: disabled
(3)	No data recovery	: disabled
(4)	LIP F8 recovery	: enabled
(5)	LIP on port bypass	: enabled
(6)	Auto cascade	: enabled
(7)	Bypass at max OS err	: disabled
(8)	Bypass at max CRC err	: disabled

(9)Bypass on clock delta err : disabled

(10)	Bypass on	switch stall	: disabled
(11)	Clear conn on sw stall		: disabled
	HW I/F:
	ASIC build number		: 0x0001
(12)	OS error	threshold	: 3	(0x3)
(13)	CRC error	threshold	: 3	(0x3)
(14)	Switch stall threshold		: 65535 (0xFFFF)
(15)	Clk error	thresh (ppm)	: 200 (0xC8)

(16)Clk error prescale (1-16) : 6

(17)Err count thresh (CSecs) : 1000

(18)Bad zone thresh (CSecs) : 500

(19)Bad zone bypass (CSecs) : 10

ACTIONS:

(20)Reset switch

(21)Reset HW

(22)Reset counters

(23)Event log

(24)Fibre Alliance event log

(25)Fibre Alliance event sev : Info

43

Image 46

Vixel 335 manual Changing the CLI/Web Password, Viewing Management, Policy, and Threshold Settings

Contents

InSpeed Model Managed Storage SwitchINSTALLATION&CONFIGURATION guide Part Number 00041363-001 Rev. A Table of Contents A p p e n d i x e s About This Guide FeaturesCHAPTER 1 Introduction Overview Vixel Model 335 Installation & Configuration Guide Fibre Channel - Arbitrated LoopInSpeed Technology CHAPTER 1 Introduction Unpacking the Switch CHAPTER 2 InstallationInstalling the Switch Small Form-Factor Pluggable SFP Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test CHAPTER 2 Installation Setting Up the Switch Attaching Devices Figure 2-1. Switch features diagram Understanding the Switch’s LEDsPower On System LEDs Indication CHAPTER 2 InstallationSystem LEDs Port LEDs Status PortBypassed Activity Cascading with Non-Overlapping Zones Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Zone Zone Zone Figure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerO v e rv i e w CHAPTER 3 Management Logging On and Off CHAPTER 3 ManagementNavigation Figure 3-1. Web Manager Home Page Resetting the Switch Configuring the SwitchConfiguration Task Location in Web Manager Description System Information SettingsSetting Figure 3-2. System Information Page Network Settings Figure 3-3. System Information Change Settings Page Switch Identification Switch SpeedSwitching Mode Blocking ARB Figure 3-5. Time Information Change Settings Page Downloading the Switch ConfigurationTime Settings Figure 3-4. Time Information Page Firmware Settings Figure 3-6. Firmware Information Page 1. Click Load New Firmware Image 1. Click Change Firmware SettingsEvent Log Messages Figure 3-7. Event Log Messages Page Figure 3-8. FC Switch Information Page FC Switch InformationFigure 3-9. FC Switch Information Page with Highlighted Zones Indication OS InformationDetection Figure 3-10. Ordered Set Information Page RRDY Figure 3-11. Ordered Set Information Page with Highlighted Zones Port Usage InformationFigure 3-12. Received Port Utilization Page Value Figure 3-14. Received Port Utilization Change Settings PageFigure 3-13. Received Port Utilization Page with Highlighted Zones Port Settings Figure 3-15. Port Information Page Figure 3-16. Port Information Page with Highlighted Zones Figure 3-17. Port Information Page with Transceiver Information Mode Figure 3-18. Cascade Information Page Figure 3-19. Cascade Information Page with Highlighted Zones Switch Policy Policy SettingsFigure 3-20. Policies Page To update the switch’s policies Figure 3-21. Policies Change Settings Page Figure 3-23. Non-overlapping Zones Zone SettingsFigure 3-22. Overlapping Zones Figure 3-24. Zone Information Page Overlapping Zones Figure 3-25. Overlapping Zone 1 Information Page Figure 3-26. Overlapping Zone 1 Information Configuration Page Non-Overlapping Zones Note Ports 11 and 12 are Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page always in Zone Highlighted Zones Using the Command Line Interface CLI Connecting to the CLI CLI Command Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling DHCP Requests tftp -i IPaddress PUT filename ramdisk Managing the FirmwareDownloading New Firmware tftp IPaddress Message Action Configuring the Trap Destination Table Option Changing the CLI/Web Password Viewing Management, Policy, and Threshold Settings Policies Policy Settings Threshold Information Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning Actions Changing the Switching Mode Command CHAPTER 3 Management Displaying Ports CHAPTER 3 Management Resetting the Switch to Factory Default Settings Resetting the SwitchResetting the Hardware Viewing the Event Log Overlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10 Technical Support ReferenceCHAPTER 4 Technical CHAPTER 4 Technical Reference Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair If the Mgmt Present LED continues to blink and POST has already Problem Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues Recommended Action Appendixes APPENDIX A Specifications S p e c i f i c a t i o n s Vixel Model 335 Operating Conditions Operating ConditionsAPPENDIX A Specifications Requirement Command CommandsConsole Commands General Commands APPENDIX B CLI Console Commands Action Commands APPENDIX B CLI Console Commands Meaning APPENDIX C Event MessagesEvent Action APPENDIX C Event Messages Event Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages Meaning Event APPENDIX D Cross ReferencesLoop ID-ALPA Arbitrated Loop Physical Addresses APPENDIX E Glossary Enables the switch to be divided into separate environments Index Index