Operating Conditions, APPENDIX A Specifications, Value | Vixel 335

APPENDIX A Specifications

Vixel Model 335 Installation & Configuration Guide	APPENDIX A Specifications

Operating Conditions

The switch must be operated in a clean, dry environment with unrestricted airflow. Air flows in through the cosmetic end and out through the business end (sometimes called the transceiver end or “back-of-box”).

To avoid overheating, maintain a minimum clearance of two inches (50.8 millimeters) on each end of the switch (the cosmetic end and the business end). Allow an adequate amount of space on the top and sides of the switch for proper air ventilation. Do not place the switch on heat-generating surfaces. Operating conditions are listed below.

Vixel Model 335 Operating Conditions

Requirement	Value

Operating Temperature	0°C to 40°C normal operation (ambient air temperature)

Storage	-40°C to 80°C non-condensing

Power	50 or 60 Hz / 100 – 250 VAC / 0.6 – 0.4 A

59

Image 62

Vixel Operating Conditions, Vixel Model 335 Installation & Configuration Guide, APPENDIX A Specifications, Requirement

Contents

InSpeed Model Managed Storage SwitchINSTALLATION&CONFIGURATION guide Part Number 00041363-001 Rev. A Table of Contents A p p e n d i x e s About This Guide FeaturesCHAPTER 1 Introduction Overview Vixel Model 335 Installation & Configuration Guide Fibre Channel - Arbitrated LoopInSpeed Technology CHAPTER 1 Introduction Installing the Switch CHAPTER 2 InstallationUnpacking the Switch Small Form-Factor Pluggable SFP Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test CHAPTER 2 Installation Setting Up the Switch Attaching Devices Figure 2-1. Switch features diagram Understanding the Switch’s LEDsPower On System LEDs Indication CHAPTER 2 InstallationSystem LEDs Port LEDs Status PortBypassed Activity Cascading with Non-Overlapping Zones Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Zone Zone Zone Figure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerO v e rv i e w CHAPTER 3 Management Logging On and Off CHAPTER 3 ManagementNavigation Figure 3-1. Web Manager Home Page Resetting the Switch Configuring the SwitchConfiguration Task Location in Web Manager Description System Information SettingsSetting Figure 3-2. System Information Page Network Settings Figure 3-3. System Information Change Settings Page Switch Identification Switch SpeedSwitching Mode Blocking ARB Figure 3-5. Time Information Change Settings Page Downloading the Switch ConfigurationTime Settings Figure 3-4. Time Information Page Firmware Settings Figure 3-6. Firmware Information Page 1. Click Load New Firmware Image 1. Click Change Firmware SettingsEvent Log Messages Figure 3-7. Event Log Messages Page Figure 3-9. FC Switch Information Page with Highlighted Zones FC Switch InformationFigure 3-8. FC Switch Information Page Indication OS InformationDetection Figure 3-10. Ordered Set Information Page RRDY Figure 3-12. Received Port Utilization Page Port Usage InformationFigure 3-11. Ordered Set Information Page with Highlighted Zones Figure 3-13. Received Port Utilization Page with Highlighted Zones Figure 3-14. Received Port Utilization Change Settings PageValue Port Settings Figure 3-15. Port Information Page Figure 3-16. Port Information Page with Highlighted Zones Figure 3-17. Port Information Page with Transceiver Information Mode Figure 3-18. Cascade Information Page Figure 3-19. Cascade Information Page with Highlighted Zones Figure 3-20. Policies Page Policy SettingsSwitch Policy To update the switch’s policies Figure 3-21. Policies Change Settings Page Figure 3-23. Non-overlapping Zones Zone SettingsFigure 3-22. Overlapping Zones Figure 3-24. Zone Information Page Overlapping Zones Figure 3-25. Overlapping Zone 1 Information Page Figure 3-26. Overlapping Zone 1 Information Configuration Page Non-Overlapping Zones Note Ports 11 and 12 are Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page always in Zone Highlighted Zones Using the Command Line Interface CLI Connecting to the CLI CLI Command Enabling or Disabling DHCP Requests Changing the Switch’s IP ParametersConfiguring Switch Information tftp -i IPaddress PUT filename ramdisk Managing the FirmwareDownloading New Firmware tftp IPaddress Message Action Configuring the Trap Destination Table Option Changing the CLI/Web Password Viewing Management, Policy, and Threshold Settings Policies Policy Settings Threshold Information Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning Actions Changing the Switching Mode Command CHAPTER 3 Management Displaying Ports CHAPTER 3 Management Resetting the Switch to Factory Default Settings Resetting the SwitchResetting the Hardware Viewing the Event Log Viewing and Understanding Zoning Information Changing the Switch’s Operating SpeedOverlapping Zoning Configuration Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10 CHAPTER 4 Technical ReferenceTechnical Support CHAPTER 4 Technical Reference Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair If the Mgmt Present LED continues to blink and POST has already Problem Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues Recommended Action Appendixes APPENDIX A Specifications S p e c i f i c a t i o n s Vixel Model 335 Operating Conditions Operating ConditionsAPPENDIX A Specifications Requirement Command CommandsConsole Commands General Commands APPENDIX B CLI Console Commands Action Commands APPENDIX B CLI Console Commands Meaning APPENDIX C Event MessagesEvent Action APPENDIX C Event Messages Event Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages Meaning Event APPENDIX D Cross ReferencesLoop ID-ALPA Arbitrated Loop Physical Addresses APPENDIX E Glossary Enables the switch to be divided into separate environments Index Index